Particularly suited where low curing temperature is required for heat sensitive components.
特别适用于需要低温固化的热敏感元件。
Under the curing temperature, it can release activing sulfur, effective sulfur content is about 27%.
在硫化温度下能释放活性硫，有效硫含量为27%。
The curing temperature of the liquid phenolic resin was slightly lower than that of powder phenolic resin.
液体酚醛树脂的固化温度稍低于粉状酚醛树脂。
Meanwhile, as the curing temperature increases, the tensile modulus of composites improves in some degree.
然而复合材料的拉伸模量随着成型温度的升高有一定幅度的提升。
These crosslinkers are stable in water at normal bath temperature but become reactive at curing temperatures.
这些交联剂于正常槽液温度下在水中很稳定，但在固化温度下就变得活泼起来。
The influences of curing temperature and alkali contents of cement on expansion of mortar bars are investigated.
研究了养护温度和水泥碱含量（质量分数，下同）与硅质集料砂浆试样膨胀的关系。
The influence of curing reaction heat on curing temperature field of cubic rubber block and tire was investigated.
探讨长方体胶块和轮胎硫化反应热对硫化温度场的影响。
As for curing process, the influence of dosage of curing agent and curing temperature on gel time was investigated.
在固化工艺方面，研究了固化剂含量和固化温度对于凝胶时间的影响。
The rapid movement of the air across the body brings the metal to the curing temperature of the paint very efficiently.
空气通过对车身的快速流动将金属提升到能使油漆有效固化的温度。
An automated system can then adjust the power output of the microwave so that a fairly constant curing temperature can be maintained.
根据温度的高低，一个自动化的系统则可以调整微波的功率输出，以便达到相对恒定的固化温度。
A model was built by using ANSYS to simulate the curing temperature field of two green tires, of which one was preheated and another was not.
采用ANSYS建立轮胎硫化温度场分析模型，对经过预热和未经预热处理两种情况下的胎坯硫化温度场进行了模拟。
The special curing mechanism, the controlled thermal decomposition and higher curing temperature make the cured resin possess great toughness.
由胺化酰亚胺热分解速度控制的、高温下相对慢的、独待的固化机理是韧性的起因。
Test shows that the curing temperature and curing time are the main factor which affect the whiteness fading and color change of printed white garment.
结果表明，白布在经后整理及成衣印花后，白度下降及颜色变化主要是由后整理及印花中的高温处理温度及时间引起的。
The influence of the original temperature of mat, high or low, to the time spent to heat the center layer to the curing temperature could be neglected;
板坯初始温度的高低对干法纤维板中心层到达胶粘剂固化温度所需加热时间的影响可以忽略不计；
The effect of the curing temperature on the strength, the CH content and the degree of C_3S hydration of the fly ash cement and pure cement was studied.
本文研究了养护温度对粉煤灰水泥及纯水泥的强度，CH含量及C_3S水化程度的作用。
The effects of PPC content, curing agent, curing temperature, curing time and adding carbon black on the mechanical properties of the blends were studied.
研究了PPC的添加量、硫化剂的种类及用量、硫化时间、硫化温度和添加炭黑对共混弹性体的物理力学性能、交联度的影响。
The finishing conditions are optimized through varying the concentrations of finishing agent, and curing temperature both at laboratory and production trial.
改变整理剂浓度、交联剂浓度和焙烘温度进行单因素试验，优选工艺条件进行实验放样和生产试验。
The results showed that the increasing of curing temperature could improve the compressive strength and shorten the curing time of fly ash based mineral polymer.
结果表明：提高养护温度可以提高粉煤灰基矿物聚合物的抗压强度，缩短养护时间。
The amount of plasticizer, film thickness, curing temperature and curing time effect the release of the DS from the tablet coated with ethylcellulose aqueous dispersion.
结论 ：乙基纤维素水性分散体可作为缓释衣膜材料。增塑剂用量、衣膜厚度、后处理温度、后处理时间等因素均影响药物的释放。
In order to determine reasonable processing parameters, heating of thermosetting molding compound in the mold and that of heat transfer after curing temperature are analyzed.
本文就模压料在模具中加热过程和达到固化温度以后的传热过程进行定量分析，以确定合理的工艺控制参数。
The effects of curing temperature, methanol concentration and membrane composition on the ionic conductivity and the methanol permeability of the membranes were investigated.
研究了膜组成、热处理温度、甲醇水溶液浓度等对膜电导率和甲醇透过率的影响。
The conformable material has notable effects such as for decrease of curing temperature and prolong of store life as well as becomes perfect new material to electric machine.
适形材料在降低固化温度和延长适用期方面有显著成效，已成为完善的电机用新型材料。
The author proposed the principle to select the curing temperature and functional relations of the viscosity with curing temperature and time for three different resin systems.
提出了选择固化温度的原则，以及三种不同树脂固化体系粘度随固化温度、固化时间变化的函数关系。
On the basis of experiments and analysing the effects of the constant temperature and curing time on the strength of fly-ash, the best curing temperature and time are obtained.
在实验的基础上通过对恒温温度及养护时间对粉煤灰强度影响的分析，得出粉煤灰制品的最佳养护温度和时间。
Also the infrared ray absorbing properties of the treated fabric can be affected by use of different kind of nano-materials under different curing temperature and concentration.
且纳米材料的浓度、种类、焙烘温度都会影响整理织物的红外线吸收性能。
The gelation time of this epoxy resin with modified liquid anhydride was related to the chemical structure and the composition of epoxy resin, curing temperature and accelerator.
环氧树脂与改性液体酸酐体系的凝胶时间与环氧树脂的结构与组成、固化温度及促进剂等因素有关；
The invention solves the problems of high curing temperature of the prior aluminum phosphate material or the carcinogenicity of chrome in a chrome and aluminum phosphate material.
本发明解决了目前磷酸铝类材料固化温度高，或磷酸铬铝类材料中铬有致癌性的问题。
When applying organic fluoride water-proof and oil-repellent agent FS-506 for finishing, the effect of dosage, curing temperature, treatment duration on the fabric are investigated.
探讨使用我国自己合成的有机氟防水防油整理剂f S- 506进行防水、防油整理时，用量、焙烘温度、时间对效果的影响。FS - 506在预烘、焙烘一步法时，也能有较好的结果。
Through analyzing each factor such as concentration of citric acid and chitin, curing temperature as well as curing time, the optimum condition is defined for the anti-crease finish.
对柠檬酸、壳聚糖及焙烘温度和焙烘时间等进行了单因素分析，确定了防皱整理的最佳工艺。
The effects of type, concentration of chain extender, curing temperature and time of silicone sealants with low modulus and high elongation on their mechanical properties were studied.
制备了不同低模量高延伸率室温硫化有机硅密封材料，并考察了扩链剂类型和用量、固化温度和时间对材料性能和交联度的影响。
应用推荐