To start the engine, one must first light the small flame beneath the hot ignition tube and crank the engine once using the crank; these preparations take only a minute.
要启动发动机，首先得点燃热管，再转动曲柄轴，发动机便启动，这些准备工作只需一分钟。
For example, using the gearbox fitted to the shell, the need for gearbox input shaft axis lines at the engine crank axis lines.
例如，将变速器装配到离合器壳上时，必须使变速器输入轴的中心线与发动机曲轴的中心线对准。
With your feet off the clutch and accelerator, crank the engine while letting off the footbrake.
不要动离合器和油门，松开脚刹，同时发动车辆。
The propeller will windmill and crank the engine.
螺旋浆将旋转并转动引擎的曲柄。
The motor car engine crank is one of automobile power unit core components, Its manufacture quality requirement is very high.
汽车发动机曲轴是汽车动力装置的核心零件之一，其制造质量要求很高。
Different machines are usually composed of several limited common structures, for example, the main structures of gas engine, compressor and punch etc are crank-slider structures.
不同的机器往往由有限的几种常用机构组成，如内燃机、压缩机和冲床等的主体机构都是曲柄滑块机构。
Crankshaft is a very important component of large Marine engine and its key part is crank.
船用曲轴是大型船用发动机的重要部件，而曲拐是曲轴的关键部分。
It can measure the oil film thickness, oil temperature, crank Angle, speed, journal center locus and minimum oil film thickness of main bearing in diesel engine.
该系统可测量内燃机主轴承的油膜厚度、油膜温度、曲轴转角、转速、轴心轨迹和最小油膜厚度。
In the engine repairs, the repair of crank rod system is very important because it affects the normal work and service life.
在发动机维修中，曲柄连杆机构的维修是重中之重，它的维修好坏对发动机的正常工作和使用寿命有很大的影响。
An automotive starter motor has many conductors and USES a lot of current to create enough rotational force to crank the engine.
当大电流流过汽车启动机的线圈时，可以产生足以让发动机曲轴转动的力矩。
Crankshaft is a very important component of large Marine engine and its key component is crank.
曲轴是大型船用发动机的重要部件，大型船用组合式曲轴的曲柄是组成大型曲轴的关键零件。
According to the basic characteristics of internal combustion engines, crank Angle domain and its frequency domain were chosen, and engine momentary speed fluctuations were divided.
根据往复式内燃机工作的本质特征，选择了与传统时间域及频率域不同的曲轴角度域及频率域，对汽车发动机的瞬时转速波动进行了划分。
Based on the method of engine crank speed fluctuation, the 58X speed sensor signal is analyzed by the input capture.
基于曲轴转速波动法，通过对发动机58齿转速信号进行分析，计算发动机每缸失火粗暴度来判断是否失火。
The utility model has practicability in the connection of the crank connecting rod component of the motorcycle engine.
它在摩托车发动机曲轴连杆组件的连接中具有极大的实用价值。
The fifth is starting system and its purpose is to change the electrical current into the mechanical energy to push the crank-shaft around. By means of this, the engine can be started.
发动机的第五系统是启动系统，其目的是将电流转化成机械能来推动曲轴旋转，通过这一点，发动机可以启动。
Based on analyzing the unbalanced force of crank-connecting rod mechanism, this paper describes the balance of motorcycle single-cylinder engine according to practices home and abroad.
在分析摩托车发动机曲柄连杆机构不平衡力的基础上，结合国内和国外的实践，总结了摩托车单缸发动机的基本平衡方法。
In the early days of cars, you actually had to crank the engine with a little handle. Now the cranking motor or starter is just powerful enough to start the engine turning.
以前的汽车需使摇柄才能使发动机启动，现在启动机或点火机已足以使发动机启动了。
To solve the poor economic and dynamic performance at high engine speed, a new crank shaft mechanism of air powered engine was proposed.
为解决高转速下动力与经济性能的下降，提出一种新的气动发动机曲轴连杆机构。
After slipping of crank shaft sleeve in large Marine diesel engine, there will appear obvious vibration and twisting on the hull and shaft system.
大型船用柴油机曲轴红套滑移以后，船体和轴系分别出现明显的振动和扭转振动。
The optimal positions of the vibration sensor should be located on both sides of the crank-shaft bearing or bottom of the engine.
传感器最佳位置是在曲轴轴承正对的发动机两侧或油底壳处。
The influence of engine frame distortion on crank rocker operation is not taken into account in traditional surface vessel design.
在水面舰艇机械的传统设计中一般不考虑机架伸缩变形对机构运行的影响。
Based on control volume model often used for steady state simulation and crank-connecting rod model, a torque generation model for a two-stroke diesel engine was established.
在常用于稳态仿真的容积法模型基础上，结合曲柄连杆机构的动力学模型，建立了二冲程柴油机的扭矩预测模型。
The crank shaft is a key part of the internal-combustion engine so that machining it with high efficiency and precision is the goal pursued by the manufacturers.
曲轴是各种内燃机的关键零件，高效、高精度加工曲轴一直是内燃机生产厂家追求的目标。
The fifth is starting system and its purpose is to change the electrical current into the mechanical energy to push the crank-shaft around. by means of this, the engine can be started.
发动机的第四个系统是起动系统，起动系统的作用是把电能转变为机械能推动曲轴转动。
A single-cylinder high-speed diesel engine with dual symmetric crank-conrod mechanism was developed and tested on a dynamometer test bed.
本文介绍了一种采用双曲柄连杆机构的高速单缸柴油机。
The results show that the Angle between maxi - mum tumble axis and crank axis generated by each cylinder in a four-valve gasoline engine varies.
发现四气门汽油机各缸产生的最大滚流轴线与曲轴轴线夹角是不同的。
It is shown that the error of transient engine speed measurement comes from both the time interval counter and crank angle measure.
瞬时转速测量的主要误差为晶振脉冲计数误差和转角计量误差。
Two site repairing methods for Type-300 diesel engine after burning of bearing liner for crank shaft are introduced.
介绍300型柴油机曲轴烧瓦后的两种现场修复法。
Two site repairing methods for Type-300 diesel engine after burning of bearing liner for crank shaft are introduced.
介绍300型柴油机曲轴烧瓦后的两种现场修复法。
应用推荐