Cover mounting core locations exceeded the drawing tolerance and must be corrected. See attachments for details.
上盖底盘的核心位置超过了图纸允许的公差，必须要纠正，请看附件的细节。
The author analyzes the core subprogram of plotting dot seriously and deals with the subprograms of typical graphics drawing in detail.
对核心绘点子程序做了认真剖析，对典型图形的绘制做了详细介绍。
According to outcrop research, drilling core analysis, and sand distributed system drawing, we analyzed the lower member of Zhiluo Formation, northeastern Ordos basin.
作者通过露头调查、钻孔岩心分析和砂分散体系制图，对鄂尔多斯盆地东北部直罗组下段进行了成因分析。
The main ways to acquire the spatial state parameters of the texture plane of orientation core are the restoration measure, drawing solution and formula computation for the present.
目前获取定向岩心结构面空间状态参数的方法主要有复位实测法、作图求解法和公式计算法。
In this paper, the advantages and possible problems of the thin cylinder drawing core mechanism of injection moulds are discussed.
论述了注射模具中薄型油压缸侧抽芯机构的特点以及可能发生的问题。
In order to improve the quality and efficiency on die casting die design with oblique pin drawing core, the traditional design process was optimized.
为了提高斜销抽芯式压铸模设计的质量和效率，对传统的设计过程进行了优化。
The article introduces the method of superhardening treating hard alloy drawing die core with thermochemistry copermeation method so as to improve its surface hardness.
介绍采用热化学共渗法对硬质合金拉丝模芯进行超硬化处理，以提高其表面硬度的方法。
It introduces the mould structure and working principle of the injection mould with inside pattern drawing from three directions for core. Point out the design gists of the mould.
介绍三面内抽芯盒盖注射模的模具结构及工作原理，并指出了该模具的设计要点。
Electro galvanized iron wire: Is take the low-carbon steel as the core, through the wire drawing, the electricity galvanization craft processing makes the metallic composite.
冷镀锌丝：是以低碳钢为芯线，通过拔丝、电镀锌工艺加工制成的金属复合材料。
The drawing process of tubular flux-cored wire is different from common steel pipe because of flux core.
由于药芯的存在，管状药芯焊丝的拉拔不同于普通的钢管拉拔。
Hydraulic drawing-core mechanism was adopted for two-side of inner-sinking in the die casting die, and pre-resetting mechanism was set to avoid the interference of core slide with ejector pin.
压铸件内凹处两侧采用液压抽芯机构抽芯，为防止滑块型芯与推杆发生干涉而设置了预复位机构；
The core theory of sheet metal forming simulation software CADEM is introduced. Taking the development of drawing die for front fender as an example, the role of CAE technology is emphasized.
介绍了板料成型CAE软件CADEM主要理论，并以汽车外覆盖件翼子板的拉延模具开发为例，阐明了CAE技术在模具开发中所起的重要作用。
Forming technologies especially deep drawing of sheets in conventional way, are certainly the core businesses of the car industry.
成形工艺尤其是传统方式的板材拉深，是汽车工业的核心技术。
Cold galvanized wire: low carbon steel for the core-line, through the wire drawing, electrical processing made of galvanized metal composite materials.
冷镀锌丝：是以低碳钢为芯线，通过拔丝、电镀锌工艺加工制成的金属复合材料。
The factors affecting the magnetism of magnetic PP fiber were studied, including content of magnetic powder, sheath-core ratio, magnetic powder variety and after-drawing.
研究了磁性聚丙烯 （ PP）纤维中磁粉含量、纤维的皮芯比、添加的磁粉种类及纤维后拉伸等对纤维的磁性能的影响。
Practices indicate that comparing with traditional oil filter, pitman style & up-drawing core structural oil filter is easier to discharge, wash and replace.
实践证明，与传统滤油器相比，拉杆式上抽芯滤油器更易拆卸、清洗和更换。
Practices indicate that comparing with traditional oil filter, pitman style & up-drawing core structural oil filter is easier to discharge, wash and replace.
实践证明，与传统滤油器相比，拉杆式上抽芯滤油器更易拆卸、清洗和更换。
应用推荐