PDF-Single Chip Ethernet data acquisition and control circuit design.
单片机的以太网数据采集与控制电路设计。
Logical control circuit design: this part includes the design of DFF, non-overlap clock generate and so on.
逻辑控制电路设计：D触发器、不重叠时钟脉冲发生器等模块的设计。
Takes advantage of multi-function control circuit design, this device can complete5 kinds of packaging mode.
多功能控制回路设计，本机可执行5种包装模式。
PM actuator was designed, and the design formula was analyzed. The control circuit design proposal of PM actuator was also given.
并对永磁操动机构的原理进行分析，总结了一些设计公式，给出了永磁操动机构控制电路设计方案。
Its primary includes channel circuit design, triggering channel circuit design, channel control circuit design and circuit's antijamming design.
其主要内容包括信号通道电路设计、触发通道电路设计、通道控制电路设计以及电路的抗干扰设计。
It Includes the doubly-fed machine integrated control experimental system control cabinet design, the main circuit design and control circuit design.
包括双馈电机综合控制实验系统的控制柜设计，主电路设计及控制电路设计。
The module design contains transmission line, bias and APC circuit of LD, low noise and high linearity RF circuit, FSK modern, monitor and control circuit design and PCB layout.
本文重点进行了光模块主要的电路包括传输线、LD偏置电路与APC电路、低噪声高线性射频电路、FSK调制与解调功能电路与监视控制功能电路的设计。
The hardware design of the module mainly presents analogue channel circuit design, A/D acquisition circuit design, digital control circuit design, power and CPCI interface design.
主要介绍CPCI数字存储示波器模块的模拟通道设计、A/D采样设计、数字控制电路设计、电源设计以及CPCI接口设计。
This paper introduces the theory of operation, measurement and control circuit design, software design of a power factor automated compensator, which is mainly designed with 8031 micro - controller.
介绍一种以邓8031单片机为核心构成的功率因数自动补偿控制器的工作原理、测控硬件电路及测控软件的设计。
On the basis of discussing the reliability theory by total distributed control systems, it puts forward the reliability design of series hardware circuit.
在简要论述集散型控制系统可靠性理论的基础上，提出放大器硬件电路的可靠性设计。
The power supply circuit, driving circuit, display circuit, software design and signal collection of the control system are outlined.
概述了控制系统的电源电路、驱动电路、显示电路与软件设计及信号采集的方法。
The design of flyback switching transformer and feedback control loop and the improvement of the circuit for considering electromagnetic compatibility are the critical technologies.
反激式开关变压器和反馈控制回路设计，以及考虑电磁兼容性对电路的改进，是其关键技术。
The design of the single chip system, sample box thermostat circuit, sample position detecting circuit and step motor control circuit are discussed.
着重讨论了单片机系统、样品箱恒温电路、样品位置检测电路和步进电机控制电路的设计。
In the design, to produce circuit TL494 as a PWM output control signals, control of the on-switch situation, the half-bridge flyback output on the basis of the power of multi-output.
在设计中，以TL 494作为PWM产生电路输出控制信号，控制开关管的导通状况，在半桥反激式输出的基础上实现了电源的多路输出。
The design method and driving circuit for microstepping control of step motor are described in the paper.
本文描述步进电机微步控制的设计方法及驱动电路。
The new practical design method and design circuit for multi-state control of multi electric machinery are provided in this paper by using the method of logical function.
通过运用逻辑函数的方法，对多台电机多种状态控制线路提出了新型实用的设计方法及设计电路。
Interface circuit and the design of control program in asynchronous transfer mode between AT89C51 single chip microcomputer system and intelligent MODEM are introduced.
介绍AT 89 C51单片机系统与智能调制解调器MODEM之间的接口电路和异步传输方式下的控制程序设计。
Therefore, applied the knowledge through me which studied to design aset of traffic lights control circuit plan.
为此，通过我应用所学的知识设计了一套交通灯控制电路的方案。
The experimental results verify that the proposed method is correct and feasible and it can simplify the circuit design of the motor control system.
实验结果证实所提出的实现方法是正确可行的，而且它可简化电机控制系统的电路设计。
The system design and implementation methods of timing control circuit for a new CMOS image sensor are proposed.
本文主要论述了CMOS图像传感器时序控制电路的系统设计和实现方法。
An improvement of logic design approach for time-sequence control circuit is presented.
本文提出了逻辑法设计时序控制电路的改进方法。
Additionally the control system's hardware circuit and software design are studied with TMS320F2407 as its core chip.
用TMS320F 2407作为系统核心控制芯片，对控制系统的硬件电路和软件设计进行了研究。
This paper introduce design method and work principle on the application of SCM to aircraft gun projecting control, and provide hardware circuit and software design process.
本文主要介绍了单片机在航炮射弹控制中的设计方法和工作原理，给出了硬件电路和软件设计过程。
The detector design consists of design and select of optic parts of an apparatus, circuit design, sampling area control and antipollution device design.
探测器的设计有：光学器件的设计和选取、电路的设计、采样区大小控制装置和防污染装置的设计。
The technique plays an important role in the proper selection of parts, thermal electrical stress control in the circuit design and derating.
说明这一方法对元器件的正确选择、电路设计中热电应力的控制和降额等可靠性设计起主导的作用。
The design method of common control circuit and CPLD, generic trouble dictionary were mainly introduced.
重点介绍其通用控制电路、CPLD设计及故障字典生成方法。
A average circuit mode control chip UC3854B is used to control each phase, thus the circuit and parameters are easy to design.
每个单相电路采用一片平均电流模式控制芯片uc 3854 B作为控制核心，电路简单，参数设计方便。
The third chapter mainly introduces the hardware design of soft starter, including the main circuit, control circuit, drive circuit, and protect circuit and auxiliary switched power design.
第三章详细介绍了软起动控制器的硬件设计，包括主电路、控制电路、驱动保护回路和辅助开关电源电路的分析和设计。
On the hardware of the system, parts of control circuit and the design and debugging of peripheral circuits are discussed thoroughly.
硬件方面主要论述了控制电路各部分及外围辅助电路的设计和调试。
In real time control system, it is important to design the clock control circuit and program.
在实时控制系统中，时钟控制电路及程序的设计十分重要。
应用推荐