In order to ensure the reliability of flywheel bolt connection, stress analysis of bolt is performed using contact analysis method.
为了确保飞轮螺栓连接的可靠性，采用接触分析法对螺栓进行了应力分析。
To avid this computational error, it comes forth finite contact elements analysis method.
为了消除这种计算误差，出现了有限元接触分析方法。
Bending stresses and contact stresses of the gears were investigated by finite element method in the static analysis.
在齿轮的静力学分析中，利用有限元的方法对齿轮的齿根弯曲应力和齿面接触应力进行了研究。
Basing on the analysis of combined axial symmetry problem by the increment theory and substructure method, this paper presents a new method for solving the elastic contact problem in general.
本文运用增量理论和子结构方法在具体分析组合轴对称问题的基础上，提出了解决一般弹性接触问题的新方法。
Aiming at sheet space structure system, the finite element method in quantitative analysis about contact problem is studied in this thesis.
针对板片空间结构这一结构形式，研究了接触问题定量化分析的有限元方法。
Method the Finite Element Method was employed to perform the stress analysis on this valve, which included the material nonlinearity, large deformation and the contact condition.
方法考虑材料非线性，大变形和接触条件建立有限元模型，采用有限元法进行应力分析。
This article presents an analysis of the contact stress of rolls in two-cross-roll straightener and gives a method for the calculation.
在实践的基础上对二辊矫直机辊面接触应力的计算进行了理论分析，给出了辊面接触应力的计算方法。
A general practical finite element analysis model for two-dimentional elastic large deformation contact problems was established using the TL method.
用TL法分析研究，建立了二维弹性大变形接触问题的一般实用有限元分析模型。
Modern contact economics begin from a complete set of concept, category and the method of analysis.
现代契约经济学的研究是从一整套概念、范畴和分析方法开始的。
The first method was loaded tooth contact analysis(LTCA), the second method was to solve nonlinear dynamics equation and the third method is to integrate torsional vibration model with LTCA.
论述了螺旋锥齿轮动力学研究的三种主要方法，即加载接触分析（LTCA）、解多维非线性方程组的方法，以及加载接触分析与周向振动模型结合的仿真分析方法。
Thus, the basis of founding loaded tooth contact analysis calculating method of hypoid gear is brought about.
其结论是建立该类齿轮副承载啮合性能分析计算方法的基础。
Further analysis of the contact interface and a more complete theory are needed to extract a reliable spin polarization message with the point contact Andreev reflection method.
利用点接触反射方法获得可靠的自旋极化信息还有赖于接触界面特征的进一步分析。而一个更切合实际的、更完善的理论成为迫切的需要。
The analysis function of MSC-MARC programs on the contact problems is introduced, and the simulation method of forming processes of quadruple-layer brazed steel tubes is also discussed in the article.
本文主要介绍了MSC MARC软件提供的接触分析功能和应用该软件模拟四层卷焊管卷曲成形过程中接触问题的处理方法。
To study the influence of O-rings secondary seals, deformation behaviors of mechanical seal faces were analyzed under different pressures with the method of integral contact analysis by FEM.
采用整体接触有限单元法，考虑“O”型辅助密封圈的影响，计算了不同压力下机械密封端面变形行为。
The mirror response based on bolt contact and the mirror deviation based on gravity and temperature loads are analyzed by contact nonlinear analysis method.
采用接触非线性分析方法对螺钉预紧时反射镜的响应及在自重和温度载荷作用下反射镜的变形进行了分析。
Contact FEM strength reduction method is an inverse process in limiting equilibrium analysis of slope stability.
有限元强度折减法可以作为极限平衡分析方法的一种逆过程。
Fast and efficient contact detection algorithm is one of the most important key techniques to control computational efficiency in 3d discontinuous analysis such as the distinct element method.
在离散元等三维非连续介质数值分析方法中，快速高效的接触检索算法是控制计算效率的关键性因素之一。
Principle analysis and experiment result indicate that the non-contact thickness measurement method using CCD as photoelectric transformation element is feasible.
理论分析及实验表明，采用CCD为光电转换元件的非接触测量厚度法是可行的。
This paper is based on the research of classical contact analysis and Finite Element Method (FEM) contact analysis.
论文对经典接触计算方法与有限元接触问题计算方法进行了对比研究。
The tooth contact analysis shows that good modification effect is achieved when the method of tooth mismatched modification is used.
齿面接触分析结果表明失配修形后接触质量良好。
The 3-d finite element model of bolt is calculated by the method of contact analysis, and the fatigue strength of bolt is checked.
并采用接触分析法对螺栓的应力应变进行了三维有限元计算，对螺栓的疲劳强度进行了校核。
In accordance with the theory of contact mechanics an analysis is made upon rolling bearings by means of finite element method and a new method of unsymmetric shape modification for roll...
根据接触力学理论，通过有限元方法对滚动轴承的分析，提出了滚子非对称修形新方法。
This paper also discussed the practical simplification of complicated structure, the complex modeling method of different kinds of element, and contact analysis problems.
在课题研究中，还探讨了复杂结构的合理简化、多种单元混合建模以及接触分析等问题。
A numerical analysis method was presented to study the behavior of the laterally loaded pile considering the characteristic of the contact interface.
采用数值方法研究了桩土接触面特性对水平受荷桩受力特性的影响，并通过对工程实例的分析验证了计算方法的有效性。
The methods of dealing with the contact problems by the finite element method are researched in this thesis, and calculation and analysis combining engineer examples are carried on.
本文就采用有限元法求解接触问题进行了研究，并结合工程实例做了计算与分析。
In the mechanism analysis of consolidation of foundation soil by heavy tamping method, the dynamic contact stress calculation of hammer bottom and foundation surface is the key technical problem.
在强夯法加固地基机理的分析中，夯？底部与地基表面的动接触应力计算是关键技术问题。
In the mechanism analysis of consolidation of foundation soil by heavy tamping method, the dynamic contact stress calculation of hammer bottom and foundation surface is the key technical problem.
在强夯法加固地基机理的分析中，夯？底部与地基表面的动接触应力计算是关键技术问题。
应用推荐