In the Configuration TAB in the testing window, remove the simulators.
在测试窗口的Configuration选项卡中，删除模拟器。
The Configuration TAB contains the basic building blocks needed to run your product.
Configuration选项卡包含运行产品所需的基本构建块。
To add or remove modules from your test configuration, you can also use the configuration TAB.
要向测试配置添加或从中删除模块，您还可以使用Configuration选项卡。
The configuration TAB allows you to view and edit the er configuration parameters of the node.
Configuration选项卡允许查看和编辑节点的ER配置参数。
Switch to the Configuration TAB of the editor and check the Enable administration console box.
切换到该编辑器的Configuration选项卡，选取Enableadministrationconsole框。
Figure 3 shows you how to create an emulator in the Configuration TAB of the integration test client.
图3显示了如何在集成测试客户端的Configuration选项卡中创建模拟器。
This panel is called a launch configuration TAB group; an example TAB group is shown at right in Figure 1.
这个面板称为launchconfiguration tabgroup；图1右侧显示了一个示例选项卡组。
The Configuration TAB gives you quick links to add and edit devices and alerts, as well as schedule reports.
配置选项卡使您可以添加和编辑设备和警报，以及计划报告的快速链接。
To remove the emulators, select the Configuration TAB and select all three for removal as shown in Figure 23.
为删除模拟器，请选择Configuration选项卡并选择删除所有三个模拟器，如图23所示。
Click the Configuration TAB, and select All Messages and Traces or fine, finer, or finest, as shown in Figure 13.
单击Configuration选项卡，选择allMessagesand Traces或fine、finer或finest，见图13。
Open the Server Configuration, navigate to the Configuration TAB, and select the Enable administration console option.
打开ServerConfiguration，导航到Configuration选项卡，选择enableadministrationconsole选项。
Specifying the trace Settings under the Configuration TAB will require a server restart for the tracing to take effect.
在Configuration选项卡下指定跟踪设置时，将需要重新启动服务器，以使跟踪生效。
In the Test window shown in Figure 15, remove EmpRegistryImport from the emulator in the Configuration TAB, then enter the values as shown, and click Continue.
在图15中所示的Test窗口中，从Configuration选项卡上的模拟器中删除EmpRegistryImport，然后输入所显示的值，并单击Continue。
The Query Service Caching section under the Configuration tab allows for manual Dynamic Query cache clearing and writing the cache state to file for one or more server groups.
Configuration选项卡下的QueryServiceCaching部分允许手动清理Dynamic Query缓存并为一个或多个服务器组将缓存状态写到文件上。
Click the J2C TAB of the server configuration editor; you will see that one of the settable resource properties is the trace level.
单击服务器配置编辑器的J2 C选项卡；您将看到其中一个可以设置的资源属性是跟踪级别。
Move to the J2C page of the configuration editor by clicking on the J2C TAB near the bottom of the view.
单击视图底部附近的J2 C选项卡转到配置编辑器的j2c页。
In the Main TAB for this new configuration, you should see a Project field and a Main class field.
在这个新配置的Main选项卡中，应该可以看到一个Project字段和一个Mainclass字段。
In the dialog that appears, create a new analysis configuration and go to the Domains TAB.
在出现的对话框中，创建一个新的分析配置，并且切换到Domains标签。
After clicking the Ports TAB in the server configuration editor, this panel opens.
单击服务器配置编辑器的ports标签后，这个页面将会打开。
You can change this behavior on the Exceptions TAB of the Out of Office configuration document by disabling this option.
可以通过在离开办公室配置文档的Exceptions选项卡上禁用该选项来更改该行为。
In the transformation configuration for this model as a source, enable the Constructor option in the Properties TAB.
在这个模型中转换配置就像一个源，可以激活properties页签中的Constructor选项。
We intentionally skipped over a few configuration options such as the Access Level TAB because these features behave differently when the List is on a plain portal page versus a Workplace application.
我们特地跳过了几个配置选项，如accesslevel选项卡，因为当List位于纯文本门户网站页面与Workplace应用程序中时，这些功能的行为会有所不同。
A TAB labelled Resource Monitoring contains the configuration parameters that are used when the schedule in context is executed.
标有ResourceMonitoring的选项卡包含了当执行上下文中的进度表时所使用的配置参数。
Select the "Main" TAB of the transformation configuration editor, and then select the Run button.
选择转换配置编辑器的“Main”选项卡，随后选择Run按钮。
The type field identifies the launch configuration, the class identifies the class that creates the TAB group, and id gives the TAB group a unique name.
type字段标识启动配置，class标识创建选项卡组的类，而id为选项卡组提供一个惟一的名字。
When you create a launch configuration, you can override the launch that is used by selecting the Targets TAB of the launcher.
在创建启动配置后，通过选择启动程序的Target附签，您可以重写要使用的启动。
From the server configuration editor, switch to the JMS TAB and create a new queue named queue (see Figure 8).
在服务器配置编辑器中，切换到jms页并且创建一个新的名为Queue的序列(图8)。
In the server configuration editor, click on the Ports TAB (at the bottom of the editor) and you will see the following pane.
在服务器配置编辑器中，单击ports标签(在编辑器的最下端)。
Select the iSCSI TAB from the top on the configuration panel.
从配置面板的顶部选择iSCS i选项卡。
Click on the Details TAB to see the editable drop down box for the plug-in configuration JNDI name.
单击Details选项卡可以看到插件配置jndi名的可编辑下拉框。
应用推荐