Under the condition of the least factor of safety, the relations are discussed between the geometry parameters of slip surfaces and the factors of safety.
并在安全系数为最小的条件下，讨论了滑动面几何参数之间以及它们与安全系数之间的关系。
The docking process of the module was analyzed. When the uncertainty about control and geometry occurs, the basic geometric condition is analyzed to finish the docking action.
根据该模块的几何特点，分析了模块的对接过程和相邻两模块对接的几何约束关系，给出了当存在几何及控制不确定性时，完成对接最基本的几何约束条件。
By using the generalized functions and creep theory, the equations of equilibrium, geometry and constitution for stepped rotating disks of steam turbine are established under the creep condition.
应用广义函数及蠕变理论，建立了汽轮机阶梯式变厚度轮盘在蠕变状态下的平衡方程、几何方程及本构方程。
Unfortunately, introducing a comprehensive set of additional parameters can produce a bad condition for normal equations under certain geometry, so that the adjusted results are poorly determined.
可惜的是，当采用一个十分庞大的附加参数组时，在某些几何条件下将导致很坏的法方程系状态，从而使测求的平差结果很差。
The kneading block geometry is calculated comprehensively according to kinematics principle and modification of geometry is made to satisfy the practical running condition.
根据相对运动学原理建立了捏合块几何形状数学模型，并根据实际运转条件，对捏合块的几何形状作了修正。
Affected by some factors, such as the channel geometry, fluid boundary condition and material properties, bubble formation process is complex.
微通道内气泡生成机理受到通道几何尺寸、流体流动边界条件、流体物性等多种因素影响，过程非常复杂。
Then on the condition of circulation and wake geometry convergence, the rotor thrust is calculated to satisfy convergence criterion of thrust.
然后在环量收敛与尾迹收敛的条件下，计算拉力以满足拉力收敛准则。
The hydraulic cartridge cone valve is chosen for the study of possibility to explore its effects of geometry parameters and boundary condition on flow field and cavitation of cone valve.
以插装型液压锥阀为研究对象，研究了几何结构参数及边界条件对锥阀流场及气穴现象的影响。
This re-stated system includes an equilibrium condition of social reproduction and three deductions, the internal relation of which can be illustrated by geometry forms.
这个重新表述的体系主要包括一个社会再生产的均衡条件和三个推论，它们的内在联系可通过几何图形表述出来。
Under the condition of the least factor of safety, the relations are discussed between the geometry parameters of slip surfaces...
并在安全系数为最小的条件下，讨论了滑动面几何参数之间以及它们与安全系数之间的关系。
Under the condition of the least factor of safety, the relations are discussed between the geometry parameters of slip sur...
并在安全系数为最小的条件下，讨论了滑动面几何参数之间以及它们与安全系数之间的关系。
It is intended to prove that the of the optimum displaying problems related with geometry data solution can be found in polynomial time, under certain condition.
证明在一定条件下，与地理相关数据的最优显示问题在多项式时间内可解。
It is intended to prove that the of the optimum displaying problems related with geometry data solution can be found in polynomial time, under certain condition.
证明在一定条件下，与地理相关数据的最优显示问题在多项式时间内可解。
应用推荐