This research provides a theoretical method for design of a full column bolt with bottom plate.
此研究为带垫板全长锚杆支护设计提供一个理论计算方法。
During concrete pouring, by selecting correct vibrating method and surveying with theodolite, the embedded precision of column bolt is assured and installation speed is improved.
混凝土浇筑过程采用正确的振捣方式和经纬仪跟踪监控，保证柱脚螺栓的预埋精度，提高了安装速度。
The unique column design has diagonal bracing at each end and tabs that bolt into the floors above and below.
独特的柱形设计在每一头都有对角线支撑，使其与上下楼层通过螺栓进行连接。
In the connection design of steel structure, the shear plate with high-strength bolt connection is extensively used at the flexible joint where the beam is connected to the weak axis of the column.
钢结构节点设计中，梁与柱弱轴方向的柔性连接常采用剪力板高强螺栓连接，螺栓群所承受的荷载有竖向力和偏心力矩。
Effects of column stiffeners, bolt arrangement, bolt number, U-steel width and U-steel extended length are studied.
研究了柱加劲肋、螺栓排列、螺栓数目、槽钢宽度和槽钢下伸长度等的影响。
Mesh column connection with the use of semi-circular bolt head square neck, with anti-theft rings and washers, to prevent the separation can be artificially demolition.
网片与立柱的连接采用半圆头方颈螺栓，配以防盗垫圈，能防止隔离栅被人为地随意拆卸。
Expression of angle section based on the result of ANSYS finite element analyse is presented at last, which provide the basis for the design of bolt- Angle beam-to-column Connection.
最后依据有限元结果分析，提出角钢截面的计算公式，为螺栓—角钢梁柱连接节点设计提供了依据。
Contact problems between concrete base surface and column base, bolt nut and neighborhood plate, bolt shank and bolt hole are simulated really.
有限元分析中模拟了底板与基础面之间、锚栓垫片与底板之间、以及锚栓与混凝土之间的接触作用。
Secondly, the design of two typical joint of the mega frame, the joint of outrigger to super-column and the long bolt joint of the belt truss, were checked.
介绍了基于性能的节点设计原则，研究了伸臂桁架与巨型柱连接节点、环带桁架螺栓拼接节点两类典型节点。
Two component anchor bolt and dowel are Afforded, a formulas to calculate the punching capacity of this slab-column connection with the effect of punching component is given in the article.
提出抗冲切锚栓和销钉两种新型抗冲切元件，给出配置抗冲切元件时板柱节点的承载力计算公式；
The structure column comprises steel tubes, a studding piece, a connecting plate, a bolt and concrete.
该结构柱包括钢管、缀件、连接板、螺栓、混凝土。
A mounting hole for arranging the high strength friction grip bolt is arranged at the top of the rectangle steel pipe column.
所述的矩形钢管柱的上部开有用于安装高强螺栓的安装孔。
The reinforcing structure is suitable for carrying out reinforcement when the intensity of the holding down bolt of the steel column is not enough.
本发明适用于对钢柱地脚螺栓强度不够时进行加固。
The reinforcing structure is suitable for carrying out reinforcement when the intensity of the holding down bolt of the steel column is not enough.
本发明适用于对钢柱地脚螺栓强度不够时进行加固。
应用推荐