The fabrication process is carefully controlled so that the grating groove and multilayer-coating parameters well meet the design targets.
由于对离子束刻蚀工艺和镀膜工艺的精细控制，光栅的槽形参数及多层膜参数良好地满足了设计要求。
In Chapter 3, the design and optimization technique of various negative dispersion mirrors were introduced, and the effect of the coating parameters to the mirrors is analyzed.
第三章介绍了不同负色散镜的设计和优化技术，以及各种参数对实际镀制负色镜的影响。
The results show that the coating film with flat, smooth and excellent performance can be obtained under the condition of appropriate electrophoretic parameters.
结果表明，在适宜的电泳工艺参数下，可以得到外观光滑平整，综合性能优良的漆膜。
In this paper, the influence of various parameters on suspension shearing dry strength and permeability of EPC coating used on steel casting through right Angle test was studied.
通过正交试验，研究了各因素对真空实型铸造铸钢件涂料的透气性、干强度、剪切力、悬浮性的影响。
However, the content of the each constituent varies obviously with coating depth owing to changes of composition and crystal parameters.
然而，由于受微区成分和结晶参数变化的影响，涂层中各组成相的含量随层深发生了明显变化。
The effects of vacuum heat treatment on ceramic coating behavior and the key technological parameters were researched.
研究了真空热处理对陶瓷涂层性能的影响以及起主要作用的工艺参数。
The results showed that the main parameters influencing the coating properties are the arc current, spraying distance and air pressure.
结果表明，影响涂层性能的工艺参数主要是电弧电流，其次是喷涂距离和雾化空气压力。
The preparation parameters were investigated by evaluation of the film coating thickness and uniformity.
以薄膜包衣厚度和均匀性为指标，考察包衣工艺参数。
The effect of the pulse discharging parameters on the formation and hardness of the TiC coating was investigated.
讨论了脉冲放电工艺参数对涂层形成与涂层硬度的影响。
Influences of main parameters such as composition of electrolyte and electrical parameters in preparing black ceramic coating by microplasma oxidation on ADC12 aluminum alloy were studied.
研究了ADC12铝合金表面微等离子体氧化法制备黑色陶瓷膜的电解液成分和电参数等对膜层性能的影响。
Some treatment parameters led to boron carbon coating above the boride layer which ACTS as a diffusion barrier and prevents a further growth of the boride layer.
一些处理参数会导致在硼化物层上形成硼-碳层，它将起着扩散垒的作用，阻止了硼化物进一步的生长。
The effects of parameters changes of electric arc spraying technology on coating structure and anti-buckling performance were discussed in this paper.
探讨电弧喷涂工艺参数变化对涂层组织、抗折弯性能的影响。
This paper briefly introduced the phosphating treatment technology Zn - Fe alloy plating, and discuss the influence of technology parameters on quality of phosphatic coating.
简要介绍电镀锌铁合金后的直接磷化处理工艺；讨论工艺参数对磷化膜质量的影响。
This model can be used as an analysis tool of many important parameters in the coating process, thereby control the disc quality...
借助模型分析旋涂工艺中的许多重要参数，从而控制盘片质量，并最终实现闭环生产控制。
Finally, the key design parameters of coating system was obtained, this system can meet ITRS requirements on uniformity of film thickness.
最后给出了镀膜系统的关键设计参数，此镀膜系统能够满足ITRS关于膜厚均匀性的要求。
Choose spraying process parameters are the main principles of the coating and improve the bonding strength of the substrate.
选择喷涂工艺参数的主要原则是提高涂层与基材的结合强度。
The results indicate that good coating quality tin coated flake Cu powder with well electric conductivity and loose specific gravity can be obtained by controlling technological parameters.
结果表明：通过控制工艺参数可以获得镀覆质量好，且具有很好导电性和低松装密度的片状锡包铜粉产品。
The influence of arc spraying parameters on the adhesive strength and wear-resistance of JCW-B coating was studied by orthogonal design test and extreme analysis.
采用正交设计方法和通过极差分析研究了电弧喷涂工艺参数对J CW - b涂层结合强度和耐磨性的影响。
On this basis, the paper established a model for predicting the plasma spray coating quality under different process parameters.
在此基础上建立预测模型，对不同工艺参数下等离子熔射层进行质量预测。
This paper used orthogonal test to select optimum parameter of material, knitting density and coating so that the comparatively better technical parameters could be found.
笔者用正交试验法对牙周再生片的材料、编织密度以及涂层的组合进行优选，得出较优的工艺参数组合。
The effect of processing parameters on porosity and the modeling of coating formation are introduced.
介绍了喷涂工艺参数对孔隙率影响及涂层形成过程的数值模拟。
Its electric performance parameters, use material, coating and carry out standard keep the same with original series of products.
其电气性能参数，使用材料，涂覆及执行标准与原系列产品一致。
Under the optimum laser cladding parameters, adding modifying agent can further fine the microstructure of coating.
在最佳工艺参数条件下加入复合变质剂可进一步细化涂层的组织。
Effect of sulfur content in nickel coating on foamed nickel performances and effect of electroplating parameters on sulfur content in the nickel coating in foamed nickel production were studied.
研究了泡沫镍生产中镀层硫含量对泡沫镍性能的影响以及电镀工艺参数对镀层硫含量的影响。
The effects of experiment parameters on the phase constitution and the structure morphologies of the coating was studied.
对涂层的组织形貌和相组成进行分析，并研究了实验工艺对涂层结构的影响。
There is a close relationship between the magnetic characteristics of iron cores and the coating method of powder and the technical parameters.
粉末的包覆方式和工艺参数同铁粉芯的磁性能有着密切的联系。
Composition, affect of each component, process routes, choice of technic parameters and application ot multicolor coating are described.
介绍了水包油型多彩涂料的组成、各组份的作用、生产工艺路线和工艺参数的选择。
Composition, affect of each component, process routes, choice of technic parameters and application ot multicolor coating are described.
介绍了水包油型多彩涂料的组成、各组份的作用、生产工艺路线和工艺参数的选择。
应用推荐