Another optimization that can be used to reduce the cost of locking is lock coarsening.
另一个可以用来降低锁定成本的优化是锁粗化(lock coarsening)。
Lock coarsening occurs when adjacent synchronized blocks may be merged into one synchronized block.
当多个彼此靠近的同步块可以合并到一起,形成一个同步块的时候,就会进行锁粗化。
Lock coarsening is the process of merging adjacent synchronized blocks that use the same lock object.
锁粗化就是把使用同一锁对象的相邻同步块合并的过程。
Even if there are other statements between the synchronized blocks or method calls, the compiler can still perform lock coarsening.
即使在synchronized块或方法调用之间有其他语句,编译器仍然能够执行锁粗化。
A second destabilizing mechanism is Ostwald ripening, also known as coarsening or disproportionation, whereby gas diffuses from smaller to larger bubbles.
第二个非稳定化机制是奥斯特瓦尔德熟化,也叫做粗化或者歧化,即气体从小的气泡里扩散到更大的气泡里。
Eutectic carbide appear coarsening with increase of vanadium.
增钒使共晶碳化物明显粗化。
The shape of pores was close to globularity when the coarsening time was prolonged.
粗化时间延长,孔隙形状更接近球形。
The improved model not only describes grain growth, but also describes coarsening of dendrite arms.
模型除了描述了晶粒的生长,同时还描述了枝晶臂的粗化。
The lower dislocation density in bainite is unfavourable for the aggregation and coarsening of carbides.
贝氏体中位错密度较低,不利于合金碳化物的聚集粗化。
Larger pore size with the dealloying time increased and coarsening of ligaments occurs in nanoporous copper.
随着去合金化时间的延长,纳米多孔铜的孔径变大,且系带出现粗化现象。
The alloy was softened mainly by recovery during the interval and coarsening of the precipitation particles.
回复和析出相的聚集粗化是造成合金软化的主要原因。
The results showed that the cracking on fish plate was mainly resulted from the grain coarsening of material.
结果表明,材料的原始晶粒粗大是产生裂纹的主要原因。
Scratching leads to swelling, cracking, "weeping" clear fluid, and finally, coarsening and thickening of the skin.
搔抓可导致肿胀、破裂、“滴出”透明液体,最终皮肤变得粗糙和肥厚。
The heat resistance of P92 steel decreased with the decreasing dislocation density and precipitated phases coarsening.
随着位错密度的降低及析出相的粗化,P 92钢的高温耐热性也降低。
In particular, hydrophobins have been found to provide both excellent foam volume stability and inhibition of coarsening.
具体的说,已发现疏水蛋白能同时提供优越的泡沫体积稳定性和对泡沫粗化的抑制作用。
Sharpness of saw blades will be improved with coarsening of grit size under the condition of constant diamond concentration.
当金刚石浓度不变时,适当增大金刚石粒度,锯片锋利性也能得到提高。
The grain coarsening behaviour towards the austenitic hot work tool steels has been studied by means of quantitative metallography.
本文用定量金相法分析和讨论了奥氏体热作工具钢的晶粒粗化行为。
The Influences of ti content on austenite gain size and grain coarsening temperature in medium-carbon boron steel have been investigated.
研究了钛含量对中碳硼钢奥氏体晶粒度及晶粒粗化温度的影响。
The noise in the information from the wells in the thin sand-mudstone interbed area with dense well network should be removed by coarsening well information.
对密井网的砂泥岩薄互层区采用井信息进行粗化去除部分干扰信息;
And depending on what other optimizations are enabled by the larger basic block, the duration for which the lock is held may not even be lengthened under coarsening.
而且根据更大的基本块支持其他何种优化,在粗化的情况下,持有锁的时间甚至可能不会延长。
The interelectrode dielectric adopts the polypropylene film with surface coarsening which is easy to impregnate so as to enhance the reliability of high-capacity capacitor.
极间介质为易于浸渍的表面粗化聚丙薄膜,特别提高了大容量电容器的可靠性。
It considers point, line and interfacial defects in the context of structural transformations including annealing, spinodal decomposition, nucleation, growth, and particle coarsening.
其中会讨论在退火、旋节点分解、成核、成长以及粒子粗粒化等结构转变之过程中,所涉及的点、线和面的缺陷。
The influence of welding thermal cycle on structure and properties in grain-coarsening region of X80 pipeline steel was investigated by weld thermal simulation technique and the charpy test.
采用焊接热模拟试验和冲击试验,研究了X80管线钢焊接热循环对粗晶区组织性能的影响。
Coarseness of the microstructure is take-and temperature - dependent. Thus, a "mean" operating temperature may be estimated with study of the coarsening kinetics and measurement of carbide size.
显微组织的粗化(老化)直接与使用时间和温度相关,因而可通过研究碳化物粗化动力学及测定碳化物尺寸来评定管段平均使用温度。
A pretreatment process before the surface of the glass fiber is plated with tin and nickel mainly comprises the following steps of: deoiling, coarsening, sensibilizing, activating, and the like.
玻璃纤维表面化学镀锡镍前的预处理工艺主要包括除油、粗化、敏化、活化等。
Coarsening grain and intercrystalline network ferrite depress crack growth resistance of the materials strongly and result in unstable propagation of crack very easily.
晶粒粗大及晶间网状铁素体强烈降低材料的裂纹扩展阻力,并极易导致裂纹的失稳扩展。
Coarsening grain and intercrystalline network ferrite depress crack growth resistance of the materials strongly and result in unstable propagation of crack very easily.
晶粒粗大及晶间网状铁素体强烈降低材料的裂纹扩展阻力,并极易导致裂纹的失稳扩展。
应用推荐