Disc bolting is then tightened in closed position.
然后阀瓣螺栓紧固在关闭位置。
The open position exposes substantially more of the air passageway than in the closed position.
在所述打开位置处暴露出的所述空气通道比在所述闭合位置处的多得多。
Just on the Closed position, the Rotary Valve will be stopped. It can avoid the material leakage.
只有在关闭位置，转阀才停止转动，可防止物料泄露；
It is possible for the user to access the menu system even when the handset is in closed position.
它有可能为用户访问该菜单系统，甚至当手机在关闭位置。
An assembly structured to selectively Orient a seal between an open position and a closed position.
一组件，其构造成在打开位置和关闭位置之间有选择地定向一密封件。
Maxium user security through snap-lock functionality & red-colour indications for open and closed position.
最大用户的安全，通过管理单元打开和关闭位置锁定功能的红色标志。
Where possible, the closed position should be determined by leak test using water or air, under low pressure.
如果可能的话，可以用水或空气，在低压状态下，对关闭状态进行测试，看看有没有泄漏。
In Electric actuators, the primary limit switches are used to control the open and closed position of the valve.
在电动执行器里，主要限位开关用来控制阀门的开启和关闭位置。
Figure 3. - This shows an analogous view of Figure 2, but when the device wheels are in the minimum closed position.
图3为与图2类似的视图，但是其中所述装置的按摩轮处于最小闭合位置。
A shutoff gate is associated with each connecting trough and movable between an open position and a closed position.
阻断闸板与每条连接槽相关联且可在打开位置与关闭位置之间移动。
They employ a unique, one piece center spool design that accommodates a user-supplied padlock in the closed position.
他们采用的是独特，一件中心轴设计，可容纳用户提供在关闭位置锁。
Unlike single-action diverter systems, the multiple-opening diverter tool is run into the hole in the closed position.
与单一动作转喷器系统不同的是，多通路转喷器是在关闭位置下入井内的。
The support nut is screwed onto the support rod against the bias of the spring to secure the window in its closed position.
支撑螺母克服弹簧的偏置旋紧到支撑杆上来保证车窗位于其关闭位置。
When locked in the closed position, the system controlled by the lockout valve cannot be operated until the padlock is removed.
当在关闭位置锁定，系统控制的锁定阀不能工作，直到锁被删除。
Slamming of check valves is the result of failure of the valve disc to reach its closed position before the fluid flow reversal.
止回阀的撞击现象，是由于在流体倒流之前，阀门的阀瓣没有到达关闭位置造成的。
Leaving the valve in a fully closed position helps prevent weld spatter from falling directly onto the mating faces of the seats.
保持阀瓣处于完全关闭位置也能够避免焊花直接掉在阀座和阀瓣的连接面上。
The spring is under compression, which means that it tries to expand and therefore spring-loads the valve in the closed position.
弹簧处于“压缩”状态时，意味着弹簧试图伸展，气门受弹簧作用而处于关闭状况。
Valves should be installed with the disc in the closed or almost closed position. This will prevent damage to the disc sealing edge.
安装阀门时，蝶板应该处于关闭或几乎关闭的位置。这是为了防止蝶板密封装置受到损坏。
The hand wheel is always in the same position relative to the valve body regardless of whether the valve is in the open or closed position.
不管阀门是在开启或是关闭位置，手轮总是处在相对于阀体的同样的位置。
A main storage compartment is formed by the first and second sections when in the closed position and serves to hold the instrument module.
以及当处于所述闭合位置时，由所述第一和第二部分构成的主容纳腔，用于容纳所述仪器模块。
But like the inlet valve, the exhaust valve needs time to reach the full-open position, it also needs time to reach the full-closed position.
但是像进气门一样，排气门需要时间到达充分打开和关闭的位置。
NOTE: the valve is shipped in the closed position. The indicator on the plastic sleeve is aligned with the vertical scribed line on the stem.
注意：阀门装运时是处于关闭位置。塑料套筒上的指示器与阀杆上的垂直刻线对齐。
Means are provided to disconnect all conductors from the service-entrance conductors and to indicate whether it is in the open or closed position.
提供切断连接电源开关导体的各种手段并标明其开启或关闭位置。
Leaving the disc in a fully closed position firmly closed also prevents weld spatter from falling directly onto the mating faces of the seat and disc.
保持阀瓣处于完全关闭位置也能够避免焊花直接掉在阀座和阀瓣的连接面上。
The amount of friction is designed to be some degree less than the return spring, so that when the pedal is released, it returns to the closed position.
设计时要确保总摩擦力小于折回弹簧的弹力，这样当松开踏板时，弹簧才会弹回，油门才会闭合。
The valve stem and sealing surfaces are completely protected from dirt and corrosion by the stem cap, whether the valve is in an open or closed position.
不管是在阀门开启位置，还是关闭位置，阀杆和密封面有阀杆盖帽的保护，能防止污物入内，防止腐蚀。
Container gripper comprising a main frame (2) and movable supporting members (7) for gripper fingers (8-9) movable between an open position and a closed position.
容器夹持器包括主架(2)和可移动的支撑件(7)，所述支撑件用于可在打开位置和闭合位置之间移动的夹持器指状物(8 -9)。
A biasing assembly may be connected to the seal structure to bias it in a normally closed position in the absence of an instrument disposed within the seal structure.
一偏置组件可连接到密封结构，以在器械不设置在密封结构内的情形下，偏置密封结构到一通常的关闭位置。
A biasing assembly may be connected to the seal structure to bias it in a normally closed position in the absence of an instrument disposed within the seal structure.
一偏置组件可连接到密封结构，以在器械不设置在密封结构内的情形下，偏置密封结构到一通常的关闭位置。
应用推荐