Design a data collection module with serial port based on microcontroller. The thesis explains the circuit principle and program designing in detail.
设计了一个串口通讯的单片机数据采集模块，文中详细阐述了模块的电路原理和程序设计。
The design of hardware circuit is explicated and the diagram of program is offered.
详细描述了硬件电路的设计，并给出了软件程序框图。
This paper detailedly introduces the whole design scheme of the system, the circuit on interface module and 89c51, the method of the software design and program flow chart.
详细阐述了系统的总体设计方案，给出了界面模块与89c51接口电路，最后介绍了软件设计方法及程序流程图。
Lastly, the hardware circuit, VHDL program design and debugging methods based on FPGA are discussed.
最后对基于现场可编程门阵列(FPGA)的硬件电路、VHDL语言程序设计及调试方法进行了讨论。
The design principle and circuit construction and program process of apparatus of the best ignition angle for motorcycle engine are introduced.
介绍了一种摩托车发动机最佳点火角试验仪的设计原理、电路结构和程序流程。
Interface circuit and the design of control program in asynchronous transfer mode between AT89C51 single chip microcomputer system and intelligent MODEM are introduced.
介绍AT 89 C51单片机系统与智能调制解调器MODEM之间的接口电路和异步传输方式下的控制程序设计。
In real time control system, it is important to design the clock control circuit and program.
在实时控制系统中，时钟控制电路及程序的设计十分重要。
Designs on motor field and structure, controller main circuit current commuting mode design, TMS320F240 least system and system program consider system normal operation under fault condition fully.
电机场路结构设计、控制器主回路换流模式设计、TMS320F 240最小系统设计、程序设计充分考虑了故障应急状态下系统正常运行必要条件。
Two kinds of program control signal attenuation circuits, which are used in circuit design, are introduced.
本文介绍线路设计中所应用的两种程控信号衰减电路。
The characteristics of a TM card and its reading-writing circuit and software program are discussed in detail, and a design of TM card watt-hour meter is introduced in brief.
详细讨论了TM卡的特点及其读写电路和软件程序，并简要介绍了一种TM卡收费电表的设计。
The dissertation introduces design of each module's hardware circuit and software program adopted modularization thinking in Front-end and Detection Base.
在文中笔者运用模块化的设计思想完成了前端和检测台的硬件电路和软件程序的设计。
Software program is designed according to hardware circuit connection and the function of each component design.
软件程序的设计是根据硬件电路图的连接和各个元器件的功能进行设计。
This model is suitable for the circuit analysis program, process tolerant analysis and device design optimization.
本模型可用于电路分析程序，工艺容错分析及器件的优化设计。
Computer aided analysis and design flow chart and program for current source inverter circuit are presented.
提出了该逆变器的通用计算机辅助分析与设计框图和源程序。
The design contains the main circuit parameters of the rectifier, drive circuit, measuring circuit and other hardware, and a full software program.
本文设计了该整流器的主电路参数，驱动电路，测量电路等硬件，提出了软件实现的完整方案。
This paper describes the top-down design method, hardware circuit buildup in detail and gives program for CPLD and single chip computer.
本文详细论述了系统自上而下的设计方法及各部分硬件电路组成及单片机、CPLD的软件编程设计。
The whole circuit USES modular design, by the main program, interruption program, launch subroutines, receiving subroutines, display subroutines etc module.
整个电路采用模块化设计，由主程序、中断程序、发射子程序、接收子程序、显示子程序等模块组成。
Some important architecture of the hardware circuit diagrams and program design diagrams are also provided.
给出了系统框图、部分硬件电路图和程序设计框图。
The design and principle of interface circuit are discussed in detail. The design of control program and the principle of the robot operation are also described.
着重讨论了接口电路的原理和设计，也介绍了机器人关节的工作原理和控制程序设计。
Parameter design on system's critical circuit is elaborated and method on system's software design is explained and diagrams are given about main program.
对系统关键部分的硬件电路进行了详细的参数设计；对系统软件设计思路进行了详细的解释，并给出了主要程序的流程图。
The paper introduces a program of high-accuracy digital tachometer based on AT89C52 SCM, and presents the diagram of applied circuit principle and software design.
本文介绍了一种基于AT 89 C52单片机的高精度数字转速计的实现方案。给出了硬件电路原理图和软件设计。
Aiming at the character of TMS320C30, the paper then indicates DSP interface circuit and program design methods, at last points out system composition.
文中针对TMS32 0c30的特点，叙述了与DSP接口电路和程序设计方法，并简要介绍整个系统的构成。
Proposed the design overall program, explained the drive circuit, simple method, easy programming and high reliability.
提出设计总体方案，阐述了驱动电路。方法简单易行，编程容易，可靠性高。
Because of simple circuit structure and high design flexibility, the program can be improved appropriately for applying to larger-size LED backlight.
该方案电路结构简单、设计灵活性高，适当改进后可适用于更大尺寸的LED背光源。
Summary: First of all, the program argues that the design of appropriate programs, there are two options, the program I: Series DC Power Supply, Option II: Integrated circuit voltage regulator.
内容摘要：首先进行方案论证，设计合适的方案，有两种方案可供选择，方案一：串联式直流稳压电源，方案二：集成稳压电路。
Hardware circuit design includes a central processing unit circuit, clock circuit, assembly language software to achieve, including the main program, subroutine, such as set-up time software modules.
硬件电路设计主要包括中央处理单元电路、时钟电路、软件用汇编语言来实现，主要包括主程序、时光设置子程序等软件模块。
Then a program is developed on the theory of EMCM (equivalent magnetic circuit method) and it is used in the pre-design of the PMSG.
然后根据等效磁路法编制了电磁计算程序，据此进行了电机的初始设计。
It mainly introduced hardware circuit design and software program programming for high-voltage circuit breaker mechanical characteristic tester.
主要介绍了高压真空断路器机械特性测试仪的硬件电路设计和软件程序的编程。
Discusses how to generate control current and provides main circuit design and software program.
讨论了控制电流波形产生方法，并给出了基本电路设计与软件编程框图。
Discusses how to generate control current and provides main circuit design and software program.
讨论了控制电流波形产生方法，并给出了基本电路设计与软件编程框图。
应用推荐