A DC supply circuit based on capacitors is presented in this paper.
本文提出一种基于电容的直流电源传输电路。
The paper introduces a design of PWM control circuit based on FPGA.
本文提出了一种采用现场可编程门阵列器件（FPGA）实现PWM控制电路的方案。
It designs the if amplifier and demodulation circuit based on TA7680.
基于TA7680设计了中频放大和检波电路。
CMOS wide band transresistance circuit based on current feedback op is introduced.
介绍了用CMOS电流反馈放大器构成互阻放大器的基本原理。
The circuit based on LM311 and CD4011 is designed to test the working state of RLG.
给出了基于LM 311和CD 4011的陀螺工作状态检测控制电路。
In this paper, the total system control circuit based on TMS320LF2407A was designed.
本文以TMS320 LF 2407 A作为主控芯片，设计了整个系统的主控制电路。
Voltage-doubler output of main topology and control circuit based on DSP are given in the paper.
文中给出倍压输出的功率主电路和数字信号处理器（DSP）控制电路。
This paper introduces a general node analysis method for the large scale circuit based on MATLAB.
介绍了用MATLAB软件实现对大规模电路进行节点分析的一种通用方法。
The realization of an angular position feedback circuit based on FPGA is presented in this paper.
介绍了基于FPGA器件的角度位置反馈电路的具体实现方法。
A class of compensating current calculating circuit based on instantaneous power theory is presented.
介绍一类基于瞬时功率理论的实时无功电流计算电路。
Establish internal communication agreement, devise the hardware decode circuit based on this agreement.
建立内部通信协议，设计出基于此协议的硬件解码电路。
A new tester for the function of TTL digital circuit based on MCS-51 single chip computer is described.
本文介绍了一种以MCS—51单片机为基础的TTL数字电路逻辑功能测试仪。
Furthermore, fault diagnosis method for controlled rectifier circuit based on neural network is explored.
此外，对基于神经网络的可控整流电路故障诊断方法进行了探索。
The intermediate frequency circuit includes QPSK modulation based on HFA3724, PLL circuit based on MB1502.
中频部分主要由HFA3724正交调制解调器和基于MB1502的锁相频率合成电路等组成。
The process of the design of the brushless torque motor control circuit based on the MSK4364 is introduced.
介绍基于MSK4364型驱动器的某型无刷力矩电机驱动电路的设计过程。
A new method in design of arbitrary order analog fractance circuit based on binomial expansion is presented.
提出一种通过二项展开式设计任意阶模拟分抗电路的新方法。
This thesis finally provide a circuit based on increase voltage and limited-current soft-starter control method.
本文最后对基于升压和限流控制方式的异步电动机软起动方法给出了具体实现方案。
This paper introduces a gain compensating circuit based on voltage-operated gain, which can realize gain compensation effectively.
本文提出了一种基于压控增益的增益补偿电路设计方案，实验表明较好地实现了增益补偿。
Through dynamic impedance matching by kernal control circuit based on C8051F020 and AD9832, the maximum output of ultrasound power is produced.
方法：基于C8051F 020和AD 9832的核心控制电路通过动态阻抗匹配法使系统输出最大超声波功率。
In this paper the designing principle of UFPA imaging circuit based on SOPC is discussed, and the structure of UFPA imaging circuit is analyzed.
介绍基于SOPC设计非致冷红外焦平面热成像电路单元的方法，并对电路的结构进行了分析。
An APFC circuit based on average current mode control is designed and tested. It is indicated that the average current mode control has many advantages.
用平均电流型控制原理设计一个APFC电路，并进行了实际测试，证明该平均电流型控制的优越性。
It introduces the project and key technology of modulation domain analysis, emphasis on the ZDT counter and the error compensation circuit based on FPGA.
介绍了调制域分析技术的原理，重点介绍基于FPGA的零空闲(ZDT)计数和测量补偿技术。
According to the problems in charging and discharging process of lithium-ion battery, a kind of protection circuit based on software and hardware was designed.
针对锂离子蓄电池在充放电过程中容易出现的过充、过放、过流、过温问题，设计了基于软硬件保护的锂离子蓄电池保护电路。
To keep the anode current stable suitably, a temperature compensated circuit based on a thermal resistor to self-regulate the filament voltage has been designed.
为使阳极电流稳定在合适的区间内，设计了一种利用热敏电阻自动调节中子管灯丝电压的温度补偿电路。
The design of CAN bus hardware interface circuit based on SJA1000, the selection of chips, the design of software and the realization of CAN communication are expatiated.
论述了基于SJA1000的CAN总线的硬件接口电路的设计、芯片的选择、软件设计及CAN通信的实现。
According to the applied characteristics of the KA3525, a regulated power supply circuit based on a PWM controlled chip and controlled by single-chip processor was designed.
根据KA3525的应用特点，设计了一种基于该电流型PWM控制芯片和单片机控制实现输出电压可调的稳压电源电路。
A reference sinusoidal circuit based on digital technique and synchronous with the line voltage is investigated. The design principle of the key circuit parameters is given.
本文研究了一种采用数字化技术，实现与电网电压同步的基准正弦电路的原理，给出了电路关键参数的设计原则。
This paper presents a new type of low noise frequency conversion circuit based on the research of phase noise conception, generation as well as relativity measurement method.
本文在对相位噪声的概念、产生及其相关测量方法研究的基础上，设计出一种低噪声频率变换电路。
It is proved by practical application that DSP control circuit based on PCI bus can not only increase the speed of data communication, but also the reliability of the system.
实践表明基于PCI总线的DSP控制电路不仅提高了数据通讯的速度，而且提高了系统控制板卡的可靠性。
This paper presents a new detecting method of kinescope's landing error, The control and data acquiring circuit based on SCM is designed to measure kinescope's landing error.
文中提出一种彩管着屏误差的检测方法，设计了以单片机为核心的控制、驱动和数据采集的彩管着屏误差检测电路。
应用推荐