The complexity of the ceramic process is taken for granted, as is the necessity for a division of labor.
复杂的陶瓷进程是理所当然的，这是有必要的分工。
The NASICON sensitive materials for ionics sensors were prepared by sol-gel process and the process was compared with the conventional ceramic process.
本文介绍应用溶凝胶工艺制备离子传感器的敏感材料NASICON，并与传统的陶瓷工艺作了比较。
The GE process for making a transducer begins by spreading onto the print table a thin layer of ceramic slurry containing a light-sensitive polymer.
通用电气制造商(GE)制造换能器的过程是首先在打印台面喷撒一薄层含有光敏聚合物的陶瓷浆料。
The clip was first exchanged for a wooden pen, which was traded for a ceramic doorknob, and the process continued right up to the house.
首先，他用区别针换到一支木钢笔，然后是陶瓷门把手，努力不懈的结果便是这座房子。
The solid fuel pellet (a ceramic oxide matrix) is the first barrier that retains many of the radioactive fission products produced by the fission process.
固体的燃料弹（陶式氧化物母体）是第一道防护，隔开裂变过程中产生的裂变放射。
Preparation of metallic ceramic coatings by thermochemical reaction method has the advantages of simple process, low cost, very strong adhesion of coatings to metal surface.
热化学反应法制备金属基陶瓷涂层具有工艺简单、成本低廉、涂层与金属表面结合力特强等优点。
Objective To study the application of inorganic ceramic membrane microfiltration coupled with ultrasonic in the process of refining Bitong medicinal liquor.
目的研究无机陶瓷膜微滤耦合超声技术在痹通药酒澄清过滤中的应用。
To discuss the ceramic fiber manufacturing process.
讨论了陶瓷纤维的制造工艺。
This article describes essential process and design of multiplayer ceramic packages, selecting of major original materials, and its some questions in the research, and production.
本文叙述了多层陶瓷外壳的基本工艺和设计，主要原材料的选用以及在科研和生产过程中的一些问题。
Based on the manufacturing process of honeycombed ceramics, this paper discusses the technologies of the preparation of plastic mass, shaping, drying, and firing of extruded ceramic products.
本文以蜂窝陶瓷生产工艺为例，讨论了陶瓷部件挤出成型过程中，塑性泥料的制备、成型、干燥和烧成等工艺技术和装备问题。
Separation of clay from vegetable oil using ceramic microfiltration membrane in the oil refining process was studied.
针对植物油精制过程，以陶瓷微滤膜对油与粘土的分离进行了研究。
The ceramic filter board is characterized with simple production process, low cost as well as prodution condition.
此陶瓷过滤板具有生产工艺简单，成本低等特点，并具备生产的条件。
Deposition of carbide ceramic coatings by the HVAF spraying process enables wear performance of drawing pulley-rings to improve greatly.
采用高速火焰（HVAF）喷涂工艺制备金属碳化物陶瓷涂层，使拉丝轮圈的耐磨性能大幅度提高。
The technological process of coprecipitation for preparing PZT piezoelectric ceramic powders is studied through orthogonal experiments.
采用正交实验方法研究共沉淀法制备PZT压电陶瓷粉体的工艺过程。
Ceramic color composition and process for producing a curved surface glass sheet employing it.
陶瓷色料组成和运用该色料生产曲线表面玻璃板的工艺方法。
In the ceramic production process, fast mensurate and efficient control powder granularity and their distribution have important meaning in raising product quality and reducing cost.
在陶瓷产品生产过程中，快速测量和有效控制粉体的粒度及其分布，对提高产品质量、降低生产成本具有重要意义。
The technological process of coprecipitation for preparing PZT piezoelectric ceramic powders is studied through perpendicular experiments.
采用正交实验方法研究了共沉淀法制备PZT压电陶瓷粉体的工艺过程。
The automatically polishing production line for deep-processing ceramic tile and the process units consisting of the line have been introduced in general.
对陶瓷墙地砖深加工的自动抛光生产线和组成生产线的工艺单机作了一般介绍。
Introduced molding process and characteristics of ceramic die-casting technology, and pointed out prevention for the ceramic die-casting common defects.
介绍了陶瓷型铸造制模的工艺过程和工艺特点，并指出了陶瓷型铸件常见缺陷及防止方法。
Every process above to prepare ceramic composites is introduced in this paper, and their different characteristics are discussed here.
本文分别介绍了这些不同的陶瓷复合材料制备工艺，并对其不同的特点进行了讨论。
The cleaning process of ceramic membranes used in treating emulsified suspension was studied.
对陶瓷膜处理乳化悬浮液过程中膜清洗工艺进行了研究。
The formulations, application process and heat treatment process, etc of metal ceramic coatings on carbon steel surface are researched.
对碳钢表面金属陶瓷涂层的配方、涂敷工艺、热处理工艺等进行了研究。
This paper analyzed the heat exchange between ceramic honeycomb regenerator and gas, and established a heat transfer process mathematical model for ceramic honeycomb regenerator.
分析了高风温燃烧系统中陶瓷蜂窝蓄热体和气体间的热量交换，建立了陶瓷蜂窝蓄热体传热过程数学模型。
Effect of struts on mechanical properties of SiC ceramic foams was investigated through analyzing struts dimension and structure of 4 kinds of ceramic foams prepared by different process.
通过分析4种不同处理工艺制备的碳化硅泡沫陶瓷孔筋尺寸和结构，探讨其对泡沫陶瓷力学性能的影响。
Then primarily informs the firing process of ceramic kiln control system devising and the structure of the system.
围绕陶瓷窑烧成过程控制系统的设计与实现展开。
The influence of material properties, machine tool system and diamond grinding wheel etc. on the machining quality of advanced ceramic components during grinding process is analyzed.
分析了高性能陶瓷零件磨削加工过程中，工件材料、加工机床性能、金刚石砂轮等方面参数对零件加工质量的影响。
Direct coagulation casting (DCC) is a novel ceramic net shape forming process for ceramic green bodies.
直接凝固注模成型(DCC)是一种全新概念的净尺寸陶瓷成型技术。
Biomimetic synthesis is a new process of fabricating inorganic ceramic coating.
仿生合成是制备无机陶瓷涂层的新途径。
The results indicate that increasing the vertical pressure or grinding speed is beneficial to the grinding process of ceramic corundum abrasive belt.
试验结果表明，采用较大的法向压力或适当增大磨削速度等磨削参数，可以高效发挥陶瓷刚玉砂带的磨削性能。
The results indicate that increasing the vertical pressure or grinding speed is beneficial to the grinding process of ceramic corundum abrasive belt.
试验结果表明，采用较大的法向压力或适当增大磨削速度等磨削参数，可以高效发挥陶瓷刚玉砂带的磨削性能。
应用推荐