A collinearity equation of the calibration parameters was derived and linearized.
建立了关于校准参数的共线性方程，并对其进行线性化。
Then, by using the camera calibration parameters, 3D coordinates of each feature point in the machine coordinate system were calculated.
由摄像机标定参数，进一步计算出各特征点在机器坐标系中的三维坐标；
Calibration parameters can be stored for up to twenty different sites so that operators can recall calibration setups from the Portaflow memory.
校准参数可以存储多达20种不同的区，使运营商能够回收该Portaflow内存校准设置。
The calibration model based on the whole measurement system makes calibration parameters inter-correlative resulting in emanative calibration process.
这种基于整体测量系统的校准模型使得校准参数相互关联，容易造成校准过程发散。
Because of adding 3 calibration parameters, the block adjustment of amplitude images and Digital Elevation Model (DEM) could be actualized at the same time.
由于改进的模型中增加了三个定标参数，因此能够同时实现多航带幅度图像以及数字高程模型(dem)的联合平差。
The calibration mode allows the image sensor generate calibration parameters which are used to improve the linearity of the sensor through a interpolation method.
校准模式允许图像传感器产生校准参数，这些校准参数通过内插法来提高传感器的线性度。
The digital setting of parameters makes for precise and rapid setup and calibration.
参数的数字化设置使精确和快速安装和校准。
Using MATLAB to realize a simple calibration method of camera parameters.
使用MATLAB实现了一种简便的摄象机参数的标定方法。
The published scope of accreditation for the calibration laboratory covers the required measurement parameters, ranges and uncertainties required by PSL.
校准实验室已公开的认证范围，包括管架集团有限公司(PSL)所需要的测量参数、范围和不确定性。
A simple and efficient calibration of monocular camera was also presented to get more accurate motion parameters.
为了更准确地估计目标的运动参数，还提出了一种简单有效的单目相机标定算法。
In this paper, we introduce the camera model calibration algorithms and adopt a method of moving a single camera to calibrate parameters of traffic monitoring system.
本文研究了摄像机模型的标定方法，采用了通过一台摄像机平行移动来模拟两个摄像机的标定方法，达到标定系统参数的目的。
The principle of exposure duration calibration is formed by adjusting exposure duration and keeping other parameters of digital color camera.
仅改变曝光时间，保持相机的其它参数不变，建立了曝光标定原理。
Reduction of the catchment area could increase the sensitivity of other parameters, providing better condition for parameter calibration.
减小汇水区面积的不确定性可提高其他参数的灵敏度，有利于参数的有效识别。
Of instrument data storage, content analysis and calibration curve parameters readily available.
仪器数据存储量大，含量分析结果和标定工作曲线参数随时可查。
The (parameters, ) setup and calibration process for PF3000 system were described briefly.
对PF3000系统使用过程中的设置与标定作了简要描述。
Calibration coefficient is a group of key parameters of an array induction logging tool.
刻度系数是阵列感应测井仪器的关键参数。
A new method of direct calibration for intrinsic parameters of camera is introduced in the paper.
从理论上提出了一种新的直接标定摄像机内部参数的算法。
This paper presents a multiple stages calibration method of CCD array camera, which separate the interior parameters and exterior parameters based on the principle of geometric projection.
提出了一种CCD阵列相机几何标定的多级处理方法。根据几何成像原理，该方法把相机内外部参数分开求解；
In this method, the dynamic model parameters of accelerometer are optimized by genetic neural network according to measurement data of the dynamic calibration.
该方法利用加速度传感器的动态标定数据，采用遗传神经网络搜索和优化动态模型参数。
This approach overcame the demerit of the theory mentioned above, therefore the precision of interior and exterior orientation parameters calibration became better.
这种方法克服了原有理论的缺陷，使标定出的相机内外方位参数更加精确、稳定。
Tested by the already calibrationed parameters, the precision of calibration is finally acquired.
最后，应用标定好的参数进行验证，获取标定精度。
According to the Range Doppler equations, the geometric calibration of SAR image can be realized using SAR imaging parameters.
依据合成孔径雷达(SAR)距离方程和多普勒方程，用SAR成像参数可实现SAR图像的几何校正。
Depth profile analysis and comparison of samples are separately conducted by three sets of SIMS instruments and main parameters of samples used for calibration are calibrated.
分别用三台SIMS仪器对样品进行了深度剖析与比对，并对用作校准目的的样品主要参数进行了定值。
In addition to grit tester can also test parameters more precise control, and can make meet ISO9000 test calibration.
此外砂砾测试仪还可以对测试参数进行更精确的控制，并可进行符合ISO 9000的测试校准。
An ECU control parameters calibration system for dual-fuel automobile was developed.
介绍了双燃料汽车ecu控制参数标定系统的设计方法。
The camera 's interior and exterior parameters are acquired by the calibration.
通过摄像机的标定，求得摄像机的内部参数和外部参数。
The method of parameters control by microcomputer of the calibration X ray device is described in the paper.
论述了核工业华北放射性计量站利用计算机技术实现自制X射线校准装置参量控制的方法。
The method of parameters control by microcomputer of the calibration X ray device is described in the paper.
论述了核工业华北放射性计量站利用计算机技术实现自制X射线校准装置参量控制的方法。
应用推荐