Firstly, the quantization study on surface roughness of old concrete which is the key control point of bonding quality was carried on by roughness test.
本文首先通过粗糙度试验对粘结界面质量检验的关键控制点——老混凝土表面粗糙度进行了量化研究。
The text introduced the test method and application in some special instances about Information technology equipment Protective Bonding Conductor in Type test and Routing test.
介绍了型式认可试验和工厂例行检验中有关信息技术设备的保护连接导体电阻的测量方法，以及在某些特殊设备上的应用。
The wire bonding failure of devices is mainly shown as the breaking off of wire bonded on the packages after temperature test, and the failure causes are related to wire bonding process and materials.
器件键合失效主要表现为温度试验后管壳上的键合点脱落，而引起失效的原因与工艺过程和键合所涉及的材料有关。
The principle of eutectic bonding was analyzed. The fabrication process of eutectic bonding was discussed, the test result of eutectic bonding was given.
分析了金硅共晶键合的基本原理，讨论了键合实验的基本工艺，给出了键合的测试结果。
The bonding strength calculating formulas are presented. Which were referred to the tensile characteristic of concrete, and shows good agreement with the test results.
给出了与混凝土本身抗拉性能相关的、与试验结果符合良好的粘结强度计算公式。
The bonding mechanism between deformed bar and lightweight concrete is discussed in this paper based on the pullout test results of 75 specimens.
本论文是通过对75个试件的拉拔试验来探讨陶粒混凝土与变形钢筋之间的粘结锚固性能。
It was revealed by push out test that the hydroxyapatite coating greatly prompt the bonding strength between implant and surrounding hard tissues.
生物力学实验结果表明，使用羟基磷灰石涂层，可以显著提高骨组织与种植体的界面结合强度。
The bonding mechanism between deformed bar and lightweight concrete is discussed in this paper based on the pullout test results of 69 specimens.
通过对69个试件的拉拔试验来探讨陶粒混凝土与变形钢筋之间的粘结锚固性能。
The failure form of joint, mechanical analysis of joint, joint design and test methods of adhesive bonding of composites are presented briefly in this paper.
本文简略叙述复合材料胶接的接头破坏形式，接头力学分析，接头设计及测试方法。
The gradient PPS/FEP composite anti-corrosive coatings were prepared on carbon steel. The bonding strength of all coating systems was determined by the pull-off test.
在碳钢表面制备了具有梯度结构的PPS/FEP复合防腐蚀涂层，采用拉开法测定了各涂层体系的结合强度。
The test results show that the adhesive has the characteristics of higher bonding strength and bright application prospects.
实验表明，该胶粘剂具有优良的粘结性能，有广阔的应用前景。
The mechanics evaluation of bonding strength between coating and substrate was performed with finite element method (FEM), and an improved test model was proposed.
采用有限元法对涂层与基体界面结合强度进行了力学模拟，并对试验模型提出了改进。
Examination of the segment (using the tap test) showed excellent bonding, with only one minor area of disbonding near the middle of the segment, which was attributed to an air bubble.
考试的部分(使用水龙头测试)显示了极佳的结合，只有一小面积剥离近中部分，这是归因于一个气泡。
This paper analysed the influence of specimen thickness on test results of surface bonding strength of thin MDF.
通过试验分析比较铣槽深度的改变对中密度纤维板表面结合强度测试结果的影响。
Under this circumstance, it is necessary to test whether the quality of the interlayer bonding meets the design requirement.
在此情况下，检验层间结合质量是否符合设计要求很有必要。
Often the test involves the measurement of the shear and flexural bond strength of a bonding agent or a comparison of bonding agents under varying environmental conditions.
通常，试验涉及测量粘接剂的剪切和挠曲粘接强度，或者在不同环境条件下对粘接剂作比较。
It was shown by experimental results that the technique was effective for rapid and intuitive testing of the bonding quality and structure of an aluminum honeycomb composite test piece.
用红外热波技术对铝蜂窝夹层胶接结构进行检测，结果表明，该技术可对试件夹层胶接质量和蜂窝结构作快速有效直观的检测。
The effects of particle volume fraction, tensile rate and interface bonding strength on the properties of GB/HDPE composites were studied by tensile test and SEM observation.
通过GB／HDPE的拉伸实验和断口形貌分析，研究了颗粒体积分数、拉伸速率、界面强度对GB／HDPE复合材料力学性能的影响。
The interfacial bonding strength has been investigated quantitatively by single-pass pendulum scratching test.
采用单摆冲击划痕法对膜基界面结合强度进行了定量研究。
The interfacial bonding strength has been investigated quantitatively by single-pass pendulum scratching test.
采用单摆冲击划痕法对膜基界面结合强度进行了定量研究。
应用推荐