Set the Layer Blend mode to "Overlay".
设置图层的混合模式为“叠加模式”。
Change the "texture" layer's Blend Mode to Multiply.
更改“纹理”图层的混合模式为正片。
Change the Blend Mode of this layer to Screenat 20%.
这层的混合模式改为滤色，透明度20%。
Set blend mode to Screen and reduce its Opacity to 45%.
设置混合模式为屏幕和减少不透明度到45%。
Change Blend mode to Screen and reduce its Opacity to 20%.
改变混合模式为屏幕和减少不透明度到20%。
Duplicate this layer again and change the Blend Mode to Overlay at 50%.
再次复制这一层和改变混合模式为叠加，透明度50%。
I changed the blend mode to Soft Light, and lowered the opacity to 15% this time.
一改混合模式为柔光，和这次降至15%的不透明度。
Step 4. Set the blend mode to 'Overlay' and change the fill opacity on 'Layout 1'.
步骤4。将图层模式设置为“叠加”，并调整一下“图层1”的填充不透明度。
Change the blend mode of the stars to Screen and drop down the opacity to around 20%.
更改星星图层的混合模式为滤色，并降低不透明度到大约20%。
I set this layer's blend mode to "overlay" to give the inner Kitty a little more pop.
再将阴影图层的混合模式设为“叠加”，以使阴影更好的融合到原图的色调中去。
Then reduce this layer's opacity to 20% and change the layer's blend mode to 'overlay'.
然后调整该图层的不透明度为20%并改变图层的混合选项为叠加。
Then reduce the opacity of this layer to 5% and the layer blend mode to: 'color dodge'.
然后调整该图层不透明度为5%，并设置图层混合选项为颜色减淡。
Then reduce the opacity of this layer to 20% and the layer blend mode to: 'color dodge'.
然后调整该图层的不透明度为20%，并改图层混合选项为颜色减淡。
Now decrease the opacity of the watercolor layer to about 70% and set its blend mode to Overlay.
现在将水彩图层的透明度减少到70%左右，将覆盖模式设置为混合模式。
Set the blend mode to screen and use a mask to hide some areas of the fog we've just created.
设置混合模式为滤色，新建蒙版隐藏掉刚做好的雾气的某些部分。
After that I gathered all layers in a new composition combining them with layer blend mode "add".
之后我在将所有图层结合添加的混合图层集中到一个新的组。
Gradient Overlay: Change the Blend Mode to Soft Light, and click the Gradient box to modify the colors.
渐变叠加：改变混合模式为柔光，并单击“渐变”对话框来修改颜色。
Create a new layer on top of all layers and call it "soft brush", then, change its Blend Mode to Overlay.
所有层上创建一个新层，顶部称之为“软刷”，然后，改变其混合模式为叠加。
Usesmaller brush to draw some lines on the lens. Change layer blend mode to Screenand reduce Opacity to 15%.
使用较小的画笔绘制镜头上的一些行。更改图层混合模式为屏幕，不透明度降低到15%。
Desaturate it and set the blend mode to Screen and opacity to 70%. Then use the levels to darken it a little bit.
将该层去色，混合模式设为滤色，不透明度70%。然后用色阶将它调暗一点。
All I needed to do was set the layer blend mode to "Multiply" to get rid of the background but still keep the tree and shadow.
我所需要做的是把图层的混合模式改为“正片叠底”，通过这种方式来在保留树及其阴影的同时去掉背景。
I also duplicated the image and set the layer blend mode to "Overlay" for a little bit more contrast as shown in THIS TUTORIAL.
然后我把图像复制了一层，将复制图层的混合模式改为“叠加”，以此来增加一点对比，这些在THIS TUTORIAL可以看到。
This is easily done by selecting the new hatch layer, then choosing "Multiply" in the layer blend mode drop down in the layers palette.
这通过选择新的图层就很容易实现，然后将图层混合模式改为“正片叠加”。
To do this, I duplicated the final image layer, desaturated it, and set the layer blend mode to "Overlay" on top of the original layer.
为了达到这个目的，我把最终的图像复制了一层并减小饱和度，然后把混合模式改为“叠加”，将其移动到原始图层最上面。
Fill the third ellipse with a pink gradient similarly to the previous one but here change its blend mode to Color and set its opacity to 60%.
为第三个圆应用一个类似的粉色渐变，但将其混合模式改为“色相”，不透明度改为60%。
I spent very little time actually cutting them out. Since the trees are typically darker than the ground, I just set the layer blend mode to "darken".
实际上我只花了一点时间来抠树，因为一般情况下，树木比地面的颜色深一些，我只需要将图层混合模式设置为“变暗”即可。
I spent very little time actually cutting them out. Since the trees are typically darker than the ground, I just set the layer blend mode to "darken".
实际上我只花了一点时间来抠树，因为一般情况下，树木比地面的颜色深一些，我只需要将图层混合模式设置为“变暗”即可。
应用推荐