The grain size at a bending part is ensured by using the cold bending method.
采用冷弯方法，可以保证弯曲部位的晶粒度。
Bending method more tape law strictly, there are many occasions tape can't test method is the coating adhesion.
弯曲法比较胶带法严格，有很多场合胶带法是无法测试镀层的附着力。
Welded pipe that bended by hot bending method with a set of specific die and welded by plasma arc welding method was used as tubular blank of SPF.
采用焊管作为管坯 ，焊管弯曲采用专用模具热弯 ，焊接采用等离子弧焊。超塑成形采用多层模结构 ，用模具来控制波形。
Since the traditional tube bending method can't meet the timing demand of aviation technology, a tube digital manufacturing method was put forward.
针对传统经验弯管无法满足航天技术日益提高的需求问题，研究导管数字化制造技术。
The traditional raytracing methods comprise the try-shooting method of the initial value problem and the bending method of the border value problem.
传统的射线追踪方法包括初值问题的试射法和边值问题的弯曲法。
The four-point-bending method is a comparatively ideal method to evaluate the adhesion strength Of vapor deposited film to matrix is given in this paper.
本文指出四点弯曲法是定性分析和定量计算气相沉积薄膜与基体结合强度的较理想的方法。
A comprehensive bending method is applied successfully to both the reformation and the design of this kind of shaping roller much better effects obtained.
用综合弯曲法成功地对成形辊进行改造设计，并取得较好效果。
A comprehensive bending method is applied successfully to both the reformation and the design of this kind of shaping roller, much better effects obtained.
用综合弯曲法成功地对成型辊轮进行改造设计，并取得较好的效果。
CZM is used as a benchmark to check the precision and applicability of beam-bending method, such as SBT (Simple Beam Theory), CBT (Corrected Beam Theory) and ECM (Experimental Compliance Method).
本文采用内聚力模型作标准来判别各种基于梁弯曲理论的方法，这些方法包括简单梁理论、修正梁理论和实验柔度法。
In this method, when one star passes in front of another, as seen from Earth, the nearer star's gravity ACTS like a lens, bending and magnifying the more distant star's light.
当天文学家用这种方法从地球上观测到一颗恒星在另一颗恒星前“走过”时，距地球较近的这颗恒星的重力就如同一个镜头，将较远的那颗恒星的光弯曲并放大。
Experimentation data shows that the principle of bending mechanism in this article is feasible, finite element model of bending mechanism is credible and its design method is dependable.
样机试验数据表明提供的压弯机构原理是可行的，压弯机构仿真有限元模型是可信的，这种设计方法是可靠的。
The computation method for the parameters of mechanics, technology and structure in op bending straightening are derived.
给出反弯校直过程中的力参数、工艺参数和结构参数的计算方法。
The least bending energy method takes the bending energy as the objective function, and gets the reasonable cable forces by seeking the least bending energy.
最小弯曲能量法以结构的弯曲应变能为目标函数，通过求出最小弯曲能量来求得合理索力。
In this paper, problems of bending of thin plates under the combined action of lateral loading and in-plane forces are studied by means of perturbation method.
本文应用摄动方法研究了薄板在侧向载荷和中面力的联合作用下的弯曲问题。
The design values of wave - induced bending moments must he first estimated, When the direct structural design method was used for general ship designing, especially for ships beyond mies.
在对常规船舶，特别是超规范船舶，进行结构的直接设计时，首先要对波浪弯矩设计值作出估计。
Theoretically analyzing the method and formula which can deduce the moment function of piles by measured bending moment through model tests.
理论分析由实测弯矩推求桩身弯矩函数的方法，公式。
Based on the experimental study, the method of calculating bending capacity of concrete beams strengthened with Carbon Fiber Reinforced Polymer is put forward.
在试验研究的基础上，提出了碳纤维加固混凝土梁的抗弯承载力计算方法，并与实测值进行了比较。
The transfer matrix method for the bending and stability of the variable section beams with shear deformation is presented.
提出了考虑剪切变形时变截面梁弯曲和稳定计算的传递矩阵法。
In solving the nonlinear bending equations, a modified power series method is proposed.
在求解非线性弯曲方程时，我们提出了修正幂级数方法。
A method for predicting the bending fatigue life of a surface quenched gear is proposed based on two-dimensional linear fracture mechanics and a computer program is developed.
基于二维线性断裂力学理论，提出了一种表面淬火齿轮的弯曲疲劳寿命预测方法，并开发了相应的计算程序。
A simplified analysis method for the ultimate strength of ship's hull girder under cyclic bending was proposed.
给出了循环弯曲载荷下船体梁极限强度的简化分析方法。
This paper studies the theory and technology of bending cubic wood and some method of softening.
本文从方材弯曲的原理出发，分析了弯曲技术及木材软化处理的一些方法。
The theory and method of bending test on nanobeam for the measurement of Young's modulus based on atomic force microscope (AFM) are introduced.
阐述了基于原子力显微镜(afm)的弯曲测试测量纳米梁杨氏模量的理论和方法。
This paper put forward a semi-analytic semi-numeric method to analyze the cold bending of the hubcap.
该文提出一种半解析半数值的分析方法，对汽车轮辋挡圈的冷弯过程进行了分析。
This paper put forward a semi-analytic semi-numeric method to analyze the cold bending of the hubcap.
该文提出一种半解析半数值的分析方法，对汽车轮辋挡圈的冷弯过程进行了分析。
应用推荐