In the paper, the bend deformation and correction technology are studied in view of automotive camshaft manufacturing practice.
文章从汽车凸轮轴制造工艺实践出发，对其弯曲变形及校正工艺进行了分析和研究。
Bend deformation often occurs on the blowing tube of the soot bl ow er during the test run, and directly affects the regular operation of the soot blower.
在试运转时，吹灰器的吹灰管常常发生弯曲变形，直接影响吹灰器的正常运行。
The analysis and the spot measure data prove the deformation of composite soil nailed wall include shear deformation, bend deformation and total deformation of soil.
由实测和理论分析表明复合土钉墙的变形是由剪切变形、弯曲变形以及墙底基底以下土体变形组成。
Measured results indicate that the bend deformation and abruption phenomenon appears very quickly when the "two-bridge-junction" method is adopted in the parallel steel plate beam.
实测资料表明，上下行并行的钢板梁桥在采用“两桥连接”加固以后，平联杆件的弯曲变形和断裂现象急剧增多。
Bend deformation is often found in camshaft manufacturing owing to its complicated structure and low stiffness, and it must be corrected to meet the demand of product quality and technology.
凸轮轴由于其结构复杂、刚性差等特点，制造过程中容易产生弯曲变形，为了保证产品及工艺的要求，必须进行校正。
The characterization of tensile-bend deformation was the core of tension leveling technology and the essence of tensile-bend deformation was cyclic repeated bend of steel strip with tension.
带钢拉伸弯曲变形过程的表征是拉伸弯曲矫直工艺研究中的关键，带钢拉伸弯曲变形过程在本质上就是带钢在张力作用下的反复弯曲变形过程。
Theoretically bend and deformation increase transmission losses in the fiber.
从理论上讲，弯曲和形变都会增大光纤的传输损耗。
The delayed elastic deformation stage came later, the bend deflection increased more quickly, and breaking life shortened with the increase of the prolongation of the maximum load hold time.
随着最大载荷保持时间的增加，塑木复合材料进入延迟弹性变形阶段越晚，弯曲挠度增加越快，断裂寿命降低。
The residual bend results from the plastic deformation imparted as the string is spooled around the radius of the reel and guide arch.
在挠性管柱绕着卷筒半径和导拱缠绕时，所给予的塑性变形造成了残留弯曲。
The deformation of frame-tube structure under the lateral load is constituted by both shear and bend deflections. The effect of shear lag must be considered for the bend deflection.
框筒结构在水平荷载作用下的变形由剪切变形和弯曲变形两部分组成，弯曲变形必须考虑正、负剪力滞的影响。
The hardening characteristic of plastic deformation is also discussed, which is useful to bend the steel tubes of awning on worksite.
利用金属材料弯曲变形时的塑变硬化特性来弯曲矩形管，较好地解决了雨阳棚骨架现场弯曲加工的问题。
By the theory of elastoplastic bend, this paper prowents a method to calculate out - of -- plane restraint and reverse deformation that are made use of to remove angle deformation in butt joints.
本文应用弹塑性弯曲理论提出了一种消除焊接对接接头角变形的平面外拘束力的计算方法，计算了极限拘束力、拘束长度和反变形的量值，并通过试验验证了方法的有效性。
The paper puts forward the concept of normal Angle of winding bend for describing the degree of distortion and deformation of malformed winding bend.
为了描述畸形河湾扭曲变形的程度，提出了河湾法向角的概念。
Aimed at the bend of poplar-straw laminated beam, the theory of delamination shearing deformation was used to analyse its bending deflection and strength, and compared the results with other theories.
针对杨木—秸秆层合梁的弯曲问题，利用分层剪切理论对其变形和强度进行了分析。并将分析结果与经典理论、一阶和高阶剪切变形理论的结果进行了比较。
The results of experiments show that tensile strength, bend strength, bend modulus and heat deformation temperature of the composite materials are increased with the increase of carbon fibre content.
随碳纤维比例的增大，该复合材料的拉伸强度、弯曲强度、弯曲模量及热变形温度均呈上升态势；而缺口冲击强度及击穿电压呈下降态势。
Equipment can not be avoided in the production process is often necessary to move the control cables will arise because of practical bend, twist and other deformation needs.
设备在生产过程中无法避免常常需要移动，而控制电缆也会因为实际操作而产生弯折，扭曲等变形需要。
The results show that there exists the tension-bend coupling deformation in the uniformly heated beam because of the non-uniform characteristic of materials.
结果表明，由于材料的非均匀性，功能梯度梁中存在拉-弯耦合变形。
The results show that there exists the tension-bend coupling deformation in the uniformly heated beam because of the non-uniform characteristic of materials.
结果表明，由于材料的非均匀性，功能梯度梁中存在拉-弯耦合变形。
应用推荐