The succeed of rolling of eccentric shaft in front and back brake will expand the application of wedge rolling.
分析了前、后制动蹄偏心轴轧制的工艺设计，推导了偏心部分的孔型曲线方程，对零件轧制的工艺调试也作了简要分析。
Three of the other cars in the convoy reported brake problems and one car did a lot of back firing but they all made it.
其他车车队中的三个报告和一个汽车刹车问题做了很多，但背部射击都做到了。
When engaging the automatic parking brake a slight groan creaked out from somewhere in the rear, a faint sound that put a faint frown on the face of the Volvo representative sitting in the back seat.
在使用自动泊车时，车后发出了一个细小的吱吱声。
There's a manual release handle on the back of the brake. But that elevator will be heavily guarded.
闸门后面应该会有手动释放把手的。但电梯肯定是重兵把守。
Paying back those loans will now be a brake on Honduras's recovery.
偿还这些贷款对于洪都拉斯的复苏来说是一种阻碍。
Turn on the engine. Release the parking brake and select the correct gear to move back onto the road.
启动发动机。松开刹车制动并选择正确的档位驶回公路。
I removed the rear brake caliper (which makes it easier to put the wheel back on later), and took the wheel off.
余删除后制动钳，并采取了车轮赶走。
The accidental quenching, occurring in the sintering process, will make the steel back of a powder alloy brake lining brittle and useless.
粉末合金刹车片在烧结后有时会意外淬火，造成刹车片钢背脆化而报废。
We see if you need new brake pads in the front or brake shoes in the back.
我们要查查前面是不是要换刹车皮，后面是不是要换刹车鼓。
According to the special requires of bridge crane, it adopts the vector control theory, has functions of regulating speed smoothly, energy feed back, sequence brake etc.
本文介绍了一个控制桥式起重机的变频调速系统，它根据桥吊的特殊性能要求，采用矢量控制方式，具备平滑调速、能量回馈、顺序制动等功能。
India is, in the words of the Zetas, the brake point holding plate movement around the world back.
印度，在齐塔人的说法中，是赞成全全国板块活动的刹车点。
The brake pedal is arranged at the back of the accelerator pedal and the width can be longer along the vertical line to ensure the rear sole of the foot completely support on the pedal.
刹车踏板设置在油门踏板之后且沿竖线方向的宽度可长些，使右脚的后掌完全支撑在其上。
This paper presents a stress analysis and selection of processing parameter in cold-pressing forming process for manufacturing the automotive rear brake back plates.
介绍了汽车后制动底板冷压成形工艺的应力分析及工艺参数的确定。
The person on the car, and then on the brake pedal is motionless, the car under put irritating to repeat the process until the brake fluid flip so far no air, then loaded back to screw.
车上的人了，然后踩刹车踏板一动不动，车下的放刺激性重复这个过程，直到制动液翻转到目前为止没有空气的时候，然后装回螺丝。
Accroding to the structure characteristics of the Santana brake pad, determined product stamping process and blank size, the die design method was introduced, and solved the bending spring back.
根据桑塔纳汽车刹车片卡子结构特点，确定该产品的冲压工艺和产品展开尺寸，介绍模具设计方案，解决产品弯曲回弹问题。
A primary counter 214 is incremented with each normal clutch brake actuation and a secondary counter 228 is incremented with each fall-back clutch brake actuation.
主计数器(214)的计数随离合器制动器的每次正常启动而增加，副计数器(228)的计数随离合器制动器的每次低效启动而增加。
The utility model solves the problem that in the past a hot rolling flat slate steel and a hot rolling wire were used to manufacture the brake shoe back, with consumption lowered.
本实用新型解决以往使用热轧平板钢和热轧线材两种材料制造瓦背的问题，降低了消耗，提高了经济效益。
There are disk brakes and drum brake, Many cars are disk brake on both front and back wheels.
刹车目前有盘刹和鼓刹，现在的车很多前后都是盘刹的。
In this paper, an annealing process has been adopted to regain the plastic property of the steel back while the other properties of CG03 brake linings are still remained.
采用一种退火工艺，在保持刹车片其它性能的同时，使刹车片钢背恢复塑性。
In this paper, an annealing process has been adopted to regain the plastic property of the steel back while the other properties of CG03 brake linings are still remained.
采用一种退火工艺，在保持刹车片其它性能的同时，使刹车片钢背恢复塑性。
应用推荐