To create the objects, you first obtain a reference to the StAX API for the payload that the SOAP stack (such as Apache Axis) pushes into the service implementation.
为了创建对象，首先对SOAP栈（如ApacheAxis）压入服务实现的载荷获得对StAXAPI 的引用。
The formulae in this paper are founded for axial piston pump whose rotor's structure is straight axis and auto-location type, but other type of pump can reference it.
文中算式以直轴自位式缸体结构的轴向柱塞泵为基本计算模型，但对于其他类型的轴向柱塞泵亦有很大参考应用价值。
Particularlya remounting of the models applied on the hinge axis and reference position ofthe lower jaw is indicated.
尤其强调的是，需要按照下颌的铰链轴位置和参考位重新上合架。
The expression of complex amplitude is given in reference plane vertical to the optical axis by far-field approximation when the line source and the principal axis are at any Angle.
在柱坐标下从微分波动方程出发，推导柱面光波的场分布，并利用远场近似条件导出当线光源与光轴成任意角度时，在垂直光轴方向的参考面上的复振幅表示。
Criterion function is designed to determine the verticality grade between the optical axis and the reference surface without the knowledge of the reference's dimension.
在无需知道参考物面尺寸的情况下，提出判定函数，调节光轴与载物台垂直。
Determined with reference to the earth's axis rather than the magnetic poles.
根据地球中轴而非磁极确定的。
Thus, an image displayed on the image display region is enlarged and projected on a position that is eccentric with reference to the reference axis.
因 此，在图像显示区域上显示的图像被放大并被投射到相对于参考轴偏心的位 置上。
A system of coordinates in which a point is located by its distance and direction (Angle) from a fixed point on a reference line (called the polar axis).
一种用点离基准线上(称极轴)固定点的距离和方向(角度)来表示点位置的坐标系统。
Continuous 5 axis machining USES either a reference surface, or two contours (which must have the same number of points) or a contour and a point.
连续五轴加工利用一参考曲面、或两个具有相同数目点的轮廓、或一轮廓一点。
Results Before and after the stress test, the intima rotation movement occurred at the majority of the short-axis sections of the plaque and the nearby reference segments during cardiac cycle.
结果多数孤立性动脉粥样硬化斑块和参考段血管内膜表面在心动周期中均发生了旋转运动；
The following week once again below the axis (as close as the reference), Fan Chou must go, the loss will be very small.
如下周再次跌破中轴(以收盘为参照)，反抽一定要走，损失会很小。
The plane perpendicular to the axis line, and the ring reference face or back of the section parallel to the ring plane, can be considered a radial plane.
垂直于轴心线的平面，与套圈基准端面或垫圈背面的切面平行的平面，可以认为是径向平面。
Influence ofd axis stator current reference on Hopf bifurcation was also discussed.
同时讨论了定子电流励磁分量给定信号对分岔条件的影响。
The high speed drilling shaft and pin cylinder system work at the same reference axis to ensure high work precision and convent operation.
高速精密钻孔主轴和钉销气缸系同基准轴线上工作，能保证工作精度高，操作方便。
The research conclusion can provide reference for other types of three-axis stabilized platforms in their design of structure and gyro installation mode.
研究结论可为其他三轴稳定平台结构设计和陀螺安装方式设计提供参考。
It provided a reference for handling and stability of multi-axis vehicle.
为多轴转向车辆操纵稳性研究提供一定的参考依据。
Starting from the wave differential equation, a method is deduced to express the complex amplitude of light wave fields in the reference plane which is vertical to the optical axis.
在柱坐标下从微分波动方程出发，推导柱面光波的场分布，并利用远场近似条件导出当线光源与光轴成任意角度时，在垂直光轴方向的参考面上的复振幅表示。
TURCK's single axis inclinometer sensor measures angular tilt in reference to gravity.
图尔克的单轴测斜仪传感器测量与重力有关的角度倾斜。
An axis external circle simulates a reference shaft line to realize the principle of the measurement of the plane to the symmetrical characteristic of the reference axis.
以轴外圆模拟基准轴线实现面对基准轴对称度测量的原理。
An axis external circle simulates a reference shaft line to realize the principle of the measurement of the plane to the symmetrical characteristic of the reference axis.
以轴外圆模拟基准轴线实现面对基准轴对称度测量的原理。
应用推荐