Draw a line at 80% on Y-axis parallel to X-axis.
在与X轴平行的Y轴的80%处画一条直线。
The arrangement includes a microwave waveguide assembly having a longitudinal axis parallel with a first axis.
该装置包括微波波导管总成，该总成具有平行于第一轴的纵轴。
The plasma tube assembly has a longitudinal axis parallel with a second axis that is substantially orthogonal with the first axis.
该等离子管总成具有平行于第二轴的纵轴，该第二轴基本上正交于该第一轴。
According to the relative position of sub-gear axis parallel shaft spur gear drive, bevel gear drive shaft and intersecting cross-axis helical gears.
按齿轮轴线的相对位置分平行轴圆柱齿轮传动、相交轴圆锥齿轮传动和交错轴螺旋齿轮传动。
Radial bearing seat together with a component, in line with the bearing axis parallel to the surface, there is support for the mounting screws of the bo…
向心轴承与座组合在一起的一种组件，在与轴承轴心线平行的支撑表面上有供安装螺钉的底板。
Radial bearing seat together with a component, in line with the bearing axis parallel to the surface, there is support for the mounting screws of the bott...
向心轴承与座组合在一起的一种组件，在与轴承轴心线平行的支撑表面上有供安装螺钉的底板。
Based on the inverse thought, an approach is presented for the dimension synthesis of a 5-axis parallel machine tool to satisfy the requirements of workspace.
基于逆向思维提出了一种满足工作空间要求的五轴并联机床的尺度综合方法。
After establishing the model for the calibration of a novel five-axis parallel machine tool, the process of calibration is simulated by minimizing inverse kinematic residuals.
建立标定模型，用逆向运动学标定方式模拟了一新型五轴并联机床的标定过程，结果表明这种标定方法的算法收敛快、鲁棒性好。
The rotating pendulum is a typical underactuated system with a rotating shaft of the motor attached to the end which is free to spin about an axis parallel to the axis of rotation of the pendulum.
旋转摆属于典型的欠驱动系统，通过驱动杆的水平转动可使欠驱动杆由垂直下摆位置转到竖直向上位置。
In this case I will assume the cylinder is falling with the axis of the cylinder parallel to the ground (so the person would land on the back).
在这种情况下，我假设该圆柱是以柱轴跟地面平行的方式下落的(这样才能使人背部着地)。
A surface having parabolic sections parallel to a single coordinate axis and elliptic sections perpendicular to that axis.
抛物面一种有与单坐标轴平行的抛物截面和与该轴垂直的椭圆截面的平面。
Again, we have to use now the parallel axis theorem.
现在我们要用，平行移轴定理。
And now there is a theorem which I will not prove, but it's very easy to prove, and that is called the parallel axis theorem.
这个公式，我不会再验证了，但它很容易证明，它称为，平行轴定理。
A conic section whose plane is not parallel to the axis base or generatrix of the intersected cone.
圆锥的一部分，其切面既不平行于轴和基面，也不平行于圆锥母线。
If I look only at the slice parallel to the X-axis then maybe I am going through the minimum.
如果我只观察平行于x轴的切面，那这应该是一个极小值点。
The easiest of all, probably, is to just go first along the x-axis to and then go up parallel to the y-axis.
最简单的会是，首先沿x轴到,然后平行于y轴走。
But now I'm going to drill a hole here, and I have here an axis l prime which is parallel to that one.
我在这里钻个洞，这是轴l撇,和那条平行。
And then up to parallel to the z-axis, C3 let's call that C3.
再沿与z轴平行方向向上运动到，我们称之为。
If a torque is applied to the disk in such a fashion that the axis of the torque is the same as that of rotation of the disk, the direction of the former will be parallel to AB.
如果力矩是这样地作用于一圆盘上，即力矩的轴与圆盘的旋转轴方向一致，则力矩的方向与ab线平行。
Conservation of angular momentum, moment of inertia, parallel axis theorem.
角动量守恒，惯量，平行轴原理。
Consider two frames, one from each camera, capturing the moving object at the same instant by a parallel axis camera system.
通过平衡轴摄像系统截取移动物体的同一瞬间的两帧图像，两台摄像机各取一帧。
Telecentric lens has parallel chief ray with its optical axis and is ideal for co-axial lighting.
远心镜头拥有与它的光轴平行的主光线，同轴照明是非常理想的。
Parallel axis theorem and Knig theorem are deduced from the two laws of rotation.
由两个转动定律导出了平行轴定理和柯尼希定理。
Parallel axis theorem and K? Nig theorem are deduced from the two laws of rotation.
摘要由两个转动定律导出了平行轴定理和柯尼希定理。
An analysis is made about Descartes rays of transparent round-section fibers-a special internal surface reflection rays of the fiber when parallel rays strike the fibers perpendicularly to fiber axis.
摘要分析了透明圆形截面纤维在垂直纤维轴光线照射时纱维内表面反射光的一种特殊现象—笛卡尔线现象。
This simplicity of the epipolar geometry of the camera system with parallel axis allows effortless identification of the top most points of object in two images.
这个平衡轴摄像系统运用简易几何学很容易的说明了两图像中物体顶点像素问题。
The length of chamfer shall be between1 and2 complete threads as measured parallel to the axis of the threaded component.
当平行于螺纹构件轴线方向进行测量时，倒角长度应该在1-2全螺纹扣之间。
From the rolling contact problem of two viscoelastic cylinders with parallel axis, a series of normal-tangent contact coupled integration equation is obtained.
从两个平行轴粘弹性圆柱体的接触问题出发，可以得到一个法向接触和切向接触耦合的积分方程组。
The Parallel axis theorem of rigid body is verified with physical pendulum.
利用复摆验证了刚体的平行轴定理。
A fault movement can be resolved into an axial component (parallel to the pipe axis), a lateral component (perpendicular to the pipe axis) in the horizontal plane and a vertical component.
断层运动可分解为轴向分量(与管轴平行)、水平面的侧向分量(与管轴垂直)和竖直分量。
应用推荐