The structural model should be built in 4 steps with the axial surface analysis as the basis, the fault-fold geometric analysis as the key, the balanced idea as the guidance and the stru.
主要遵循4个基本步骤，轴面分析是基础，断层褶皱形态分析是核心，平衡观念是灵魂，构造复原是手段。
Moving path lines, tangential and axial average velocities of particles at the vortex surface are obtained by the photography method.
通过摄像法得出了旋涡表面流体质点的运动轨迹、切向和轴向时均速度。
On the outer surface of the pipe, the axial residual stresses of the weld and in its vicinity are compressive while the hoop stresses keep tensile.
在管道接头外表面焊缝中心处的轴向残余应力为压应力，而环向残余应力为拉应力。
For the increase of finishing efficiency and surface quantity, the vibration mechanism was used in finishing machine so as to realize the motion of axial vibration.
为了提高研磨效率与表面质量，在研磨机床中采用振动机构来实现轴向振动运动。
A general method for designing magnetic field gradient coils on a cylindrical surface with an axial magnetic field to be used in NMR imaging is suggested and developed.
系统地介绍了用于磁共振成像系统中具有轴向磁场的圆柱型表面梯度线圈的设计与优化。
Many inessential factors are becoming more important, such as the viscous dissipation, axial conduction and surface wettability.
许多在常规尺度下不重要的因素如黏性耗散、轴向热传导和表面浸润性等都开始变的突出。
Methods CT findings on axial, MPR and surface shaded display(SSD)images in 28 patients with 30 calcaneal fractures were analyzed, and the fractures were classified and appropriately treated.
方法分析28例30个跟骨骨折的轴位CT、MPR及表面重建（SSD）CT的表现，对骨折进行分型，并选择合适的治疗方案。
Damage state: when in the installation and removal of such use to the raceway and the rolling surface wounds caused by the axial linear.
损伤状态：当在安装和使用这种搬迁到滚道和滚动表面轴向线性造成的创伤。
Ventilation of starting rotation device ventilation pipe is from Axial flow of swirl hole inner surface takes air leads to vacuum cavity, model existence of scale effect.
起旋室通气井通风系由旋流洞内表面轴向水流“挟带”空气而致空腔内气体压强减小进入，模型存在缩尺效应。
The kinetic energy is distributed asymmetrically in the axial direction, and the asymmetry variation is a function of the rotational speed due to the influence of the free surface.
由于自由液面的作用，湍动能在高度方向上呈非对称性分布，并且这种非对称性随转速的变化而变化。
The reference standard for solid bars shall contain a longitudinal (axial) reference notch on the outside surface.
实心棒对比试块应在外表面制备纵向槽。
The more exact object image law of reflection image on axial spherical surface is presented, the lateral magnification and aberration are discussed.
本文给出了二级近似时近轴球面反射成像的物象规律，进而讨论了横向放大率与像差。
It is also preferable that the ratio of the axial length of the inner foot portion at its engagement surface to the axial length of the foot portion at its engagement surface is greater than 0.5.
优选的，内足部在其接合表面处的轴向长度与足部在其接合表面处的轴向长度的比值大于0.5。
This essay adopts limited units of axial symmetry and theory of system recognizing backcalculation, in which the dynamic effect of the road surface reaction to load of FWD is considered.
采用轴对称动力有限元结合系统识别反分析理论进行路面模量反算，考虑了落锤式弯沉仪（FWD）荷载作用下的路面反应动力效应。
The unsteady surface pressure on stator blade of an axial compressor was measured by means of mounting micro-sensors on blades surface.
本文对一台单级轴流压气机静子叶片非定常表面压力进行了测量。
The lateral atlantoaxial joint surface is tilted in the sagittal plane or occipito-atlanto-axial joints are asymmetric. Each of the case may result in atlantoaxial dislocation.
寰枢外侧关节面在矢状面上倾斜，枕骨髁、寰椎、枢椎关节发育不对称，可能是导致寰枢椎脱位的另外原因。
A new hydraulic design method and the numerical method of axial flow pump impeller are introduced. The integral equation for flow calculation of S1 stream surface of impeller is derived.
介绍了一种新的轴流泵叶轮的水力设计方法，推导了求解叶轮s 1流面流动的积分方程。
A method for the performance prediction of axial-flow turbines with bowed and conventional vanes is presented, which USES flow function as control equation on S2 surface.
给出了一个以S2流面流函数为主控方程的具有弯曲叶片的涡轮级性能预测的通流计算方法。
The five points difference method is used to calculate the voltage distribution on the meridian surface of axial-symmetrical electrostatic lens.
采用五点差分法计算轴对称静电透镜子午面上电位分布，再从普遍轨迹方程求得的电子轨迹出发得到透镜焦点和球差。
The dependence relations among compressive strength, splitting tensile strength and axial tensile strength of RCC with layer surface have been obtained.
试验给出有层面碾压混凝土抗压强度、层面劈拉强度、层面轴拉强度间相关关系。
Cylindrical roller adopt convexity process, so the presses of roller and race surface are proportional spacing, they can bear a large axial load, furthermore axial rigidity is strong.
圆柱滚子采用凸面加工，因此滚子与滚道之间的压力分布均匀。可承受较大单向轴向负荷，且轴向的刚性较强。
Holographic photograph is applied to study surface deformation of core-contained rock samples under single-axial pressure and visible image of off-surface displacement field is displayed.
用激光全息干涉法研究了在单轴压力下的镶嵌试件的表面形变，显示了离面位移场的可见图象。
Holographic photograph is applied to study surface deformation of core-contained rock samples under single-axial pressure and visible image of off-surface displacement field is displayed.
用激光全息干涉法研究了在单轴压力下的镶嵌试件的表面形变，显示了离面位移场的可见图象。
应用推荐