Partial buckling of hoist boom is analyzed with ANSYS finite element program.
采用ANSYS有限元程序分析起重臂的局部屈曲。
By ANSYS finite element software, the test beams were simulated and analyzed.
通过ANSYS非线性有限元软件，对试验梁进行了模拟分析。
And compared with the theory value, proved the ANSYS finite element analysis are feasible and reliable.
并与理论计算值相比较，以证明ANSYS有限元分析的可行、可靠。
The plane frame is calculated under horizontal load-wind and earthquake by using ANSYS finite element analysis software.
利用有限元分析软件ANSYS对某平面框架进行水平荷载——风荷载、地震荷载作用下内力计算，并同手工计算方法进行了比较。
And the ANSYS finite element analysis is used to choose the number of hydraulic pressure vats, which are distributed in the pile gripper.
并采用A NSYS有限元分析方法对夹桩器上均布液压缸数进行了选择。
Make use of table analysis, modal analysis of ANSYS finite element software motive force to analyze shake stress analysis of the arch dam.
利用ANSYS有限元软件动力分析中的谱分析、模态分析功能，对拱坝进行地震动应力分析。
This paper compute and analyze two dimension electromagnetic field of discal magnetoelectric machine using ANSYS finite element analysis software.
本文应用有限元软件ANSYS分析计算盘式永磁电机的二维电磁场。
The prediction model of temperature field in the process of wearing water-cooled of angle steel was set up using ANSYS finite element analysis software.
针对角钢穿水冷却过程，借助ANSYS有限元分析软件，建立角钢穿水冷却过程温度场的预报模型；
The influence of the channel parameters of the water-cooled Si mirror on temperature and thermal deformation was simulated using ANSYS finite element analysis.
采用ANSYS有限元软件详细地研究了强激光作用下水冷硅镜的沟槽结构对镜面温升和变形峰谷值的影响。
The author built a 3D partial finite element model by ANSYS finite element analysis software to make a research on the fatigue details from 2 kinds of closed vertical ribs.
为研究两种不同闭口肋的疲劳细节，使用ANSYS有限元分析软件建立三维局部有限元模型。
The model was established by using the ANSYS finite element analysis software, and the alternation regularity between anodic resistance and its numbers of days was researched.
本文利用ANSYS有限元软件，对水平地震作用下考虑和不考虑土和结构相互作用的高层建筑进行弹塑性对比分析。
The internal force of the unsymmetrical and symmetrical double-tower connected structures which are effected by wind and vertical loads is analyzed by using ANSYS finite element.
本文运用ANSYS有限元分析软件对不对称双塔连体结构和对称双塔连体结构进行了风荷载和竖向荷载作用下的内力分析。
Expression of angle section based on the result of ANSYS finite element analyse is presented at last, which provide the basis for the design of bolt- Angle beam-to-column Connection.
最后依据有限元结果分析，提出角钢截面的计算公式，为螺栓—角钢梁柱连接节点设计提供了依据。
And then the ANSYS finite element software is adopted to simulate the temperature field of the actual walls, which directly shows the temperature distribution of the computational zone.
然后利用ANSYS有限元软件对实测墙体的温度场进行模拟，直观的表示出温度分布情况。
This paper studies the performance of internal pressure blasting and external pressure squirm between smooth tube and corrugated tubes from the ANSYS finite element analysis and testing.
本文从ANSYS有限元分析和试验两方面分别对光管和波节管在承受内压爆破和承受外压失稳时的性能进行研究。
Based on the theory of the unsteady temperature field and stress field, three-dimensional finite element model is set up. The wall is analyzed by program of ANSYS finite element analysis.
本文根据瞬态温度场和应力场理论，建立地下室混凝土墙体的三维有限元分析模型，利用有限元分析程序ANSYS对基本工况下的墙体进行分析。
The stress of the approach bridge was gotten through field loading experiment, and the maximum stress of members of the approach was obtained by ANSYS finite element calculation software.
通过现场加载试验测得栈桥的应力，并利用ANSYS有限元计算软件计算出栈桥各构件的最大应力。
Using the ANSYS finite element analysis software, thermal analysis and thermal stress analysis of side dam in the strip casting process are carried out to explain the cause of side dam cracking.
采用ANSYS有限元分析软件，分析了侧封板在铸轧过程中温度场和热应力场，由此解释侧封板产生裂纹的原因。
Three contact stiffness values are calculated and ANSYS finite element analysis result and Hertz's solution are compared, results show that solving contact problem by ANSYS software is accurate.
在计算中，选取了三种不同的接触刚度分别进行分析，并将分析结果与赫兹理论解进行比较，证明ANSYS在求解接触问题时能得到更精确的解。
Using the finite element method software ANSYS, the stator temperature field of the hydroelectric generator is analyzed and calculated, the corresponding temperature field picture is given.
在此基础上应用有限元法的通用软件ANSYS，对大型水轮发电机定子温度场进行分析与计算，绘制了相应温度场图。
Based on heat transferring, a thermal field model of Laser Inner Cutting system was established and numerically simulated with the help of finite element software ANSYS.
在传热学的基础上建立了激光焦点在透明材料内部作用时的温度场模型，借助于大型有限元分析软件ANSYS进行了数值模拟。
The thermal module of the finite element software ANSYS is used to analyze the heat transfer of the gearbox.
该研究使用ANSYS有限元软件的热分析模块进行变速箱热传导分析计算。
The thermal module of the finite element software ANSYS is used to analyze the heat transfer of the gearbox.
该研究使用ANSYS有限元软件的热分析模块进行变速箱热传导分析计算。
应用推荐