Within the range of machining, if the helix Angle adopts a bigger value, it may improve the meshing performance and develop the advantages of double enveloping TI worm gearing.
在加工允许的范围内，螺旋角取较大的数值，能够较好地改善啮合性能，从而发挥二次包络TI蜗杆传动的优势。
In this paper, the axial section profile of worm with straight generatrix is analyzed and calculated according to Angle projection calculating.
本文利用角度投影计算法对直纹蜗杆轴向齿形进行了分析与计算。
This paper describes the establishing process of the equation of working profile curved surface of worm CAM mechanism, the calculation of its pressure Angle and normal curvature.
介绍了圆锥滚子蜗杆凸轮机构的轮廓曲面方程的建立、压力角和啮合曲面法曲率的计算过程。
Minimal film thickness and central film thickness of arc cylindrical worm drive were calculated under different rotation Angle.
计算了圆弧圆柱蜗杆传动在不同的蜗杆转角下的中心膜厚和最小膜厚。
It was proved in practical measurement experiments that the principle of measuring gear integrated error with a small pressure Angle measurement worm was correct and the technology was possible.
经过实际测量实验，证明了小齿形角工具蜗杆测量齿轮整体误差原理上的正确性，技术上的可行性，展示出此项新技术的潜在优势及应用前景。
This paper presents a calculating method for the edge of a new hob with straight groove and zero rake Angle. The original section edge of the said hob is on the surface of basic worm.
本文提出了对直槽零前角滚刀，原始截面刃形在基本蜗杆齿面上，其新滚刀刃形的计算方法。
When the worm crisscross Angle, still need to ensure that's too, and worm gear and worm helical screw to must be identical.
当蜗轮蜗杆的交错角为时，还需保证，而且蜗轮与蜗杆螺旋线旋向必须相同。
The following conclusion is obtained. In the cases of straight gash, spiral gash, zero rake angle and positive rake angle, the hob worm profile from hob put into use to hob abandoned i…
结果表明：在直槽或螺旋槽、零前角或正前角等情况下，用本文设计的磨轮铲磨的滚刀，其基本蜗杆轴截形在从新到旧的整个使用过程中都是精确的。
The influence of the base worm radius, the module of shaper, the teeth number and the pressure Angle on the singularity point were analyzed, respectively.
分别分析了基蜗杆半径、插齿刀模数、齿数、压力角对基蜗杆曲面奇异点位置的影响。
The worm and worm among plane within the modulus and pressure Angle, namely the worm gear were equivalent modulus is equal to the end of the worm shaft side modulus and for standard;
中间平面内蜗杆与蜗轮的模数和压力角分别相等，即蜗轮的端面模数等于蜗杆的轴面模数且为标准值；
Worm gears are adopted for driving rotational motion along azimuth Angle and power screws are used for raising zenith Angle.
蜗轮与蜗杆被用来驱动方位角的转轴，仰角的转动则使用螺杆。
A new kind of Angle adjusting device for disk pelletizer is introduced in this paper. It is a manual worm gearing with an Angle indicator.
本文介绍了圆盘造球机的一种新型调角装置，即为具有角度指示器的手动蜗轮蜗杆装置。
A new kind of Angle adjusting device for disk pelletizer is introduced in this paper. It is a manual worm gearing with an Angle indicator.
本文介绍了圆盘造球机的一种新型调角装置，即为具有角度指示器的手动蜗轮蜗杆装置。
应用推荐