Another quality of line that's more difficult to achieve is variation in the softness and hardness.
线的另一性质更加难以企及,那便是软硬的变化。
I think I can feel her weakness when she was in trouble and hardness, but all she does proves that she would never be struck down by the reality.
我想我能够体会到她陷入困苦时的脆弱,但是她所做的一切证明了她不会被现实打倒。
He is a man of brick: as if he HAD been born as a baby literally of clay and decades of exposure have baked him to the color and hardness of brick.
他是条硬汉子:好像生来就是泥质的,几十年的风风雨雨把他烧得像砖一样又黑又硬。
There are natural sceneries as well as artificial ones, both rich in the beauty of movement and tranquility, softness and hardness, black and white.
就其山水而言,包括自然山水与人工山水,二者均富于动静、软硬、黑白之美。
It is found that the structure and hardness of the plates are closely related to W content.
结果表明,镀层结构和性能与镀层中的W含量密切相关。
Their fracture toughness and hardness were determined with Vicker's indentation test machine.
在维氏硬度仪上测试断裂韧性和硬度。
This failure analysis was performed by using macro check, micrography and hardness measurement.
采用宏观分析、显微检验和硬度测定对压铸模进行了失效分析。
Next, consider the effect of the thickness of plates on the microstructure and hardness in HAZ.
并藉著板厚的改变探讨其对热影响区之金相组织与硬度造成之影响。
The finite- difference method is used in calculations on electronegativity and hardness of 103 elements.
并用有限差分方法计算了这103种元素的电负性和硬度。计算中考虑了相对论效应。
The fracture of motorcycle rear axle has been analyzed through optical microscope, SEM and hardness test.
采用光学显微镜、扫描电镜、硬度测试等方法,对摩托车后轮轴断裂件进行了分析。
The effect of grinding depth on work piece surface hardness and hardness layer depth is important factor.
磨削深度是影响工件表面硬度和磨削淬硬层厚度的主要因素。
The relationships of current density with deposition rate, crystal size and hardness of deposit were studied.
研究了电流密度与沉积速度、晶粒尺寸及镀层硬度的关系。
The microstructure and hardness of the laser modified surface are governed by the laser processing parameters.
激光表面改性层显微组织与显微硬度受激光处理工艺参数的控制。
The effects of pulse peak current density on the texture and hardness of electrodeposited Ni were investigated.
考察了脉冲峰值电流密度对纳米晶镍镀层织构和硬度的影响。
The effect of the pulse discharging parameters on the formation and hardness of the TiC coating was investigated.
讨论了脉冲放电工艺参数对涂层形成与涂层硬度的影响。
Fatigue tests were performed using the 3d dumbbell specimens with different levels of maximum strain and hardness.
使用具有不同最大应变和各种硬度的3d哑铃状试样进行了疲劳试验。
The microstructure, chemical composition and hardness of cracked jaws of wire clippers were detected and analyzed.
对已开裂断线钳钳头的显微组织、化学成分和硬度进行了检测和分析。
Parameters were the shade of color and hardness of the scar tissue, thickness and size of scar, and subjective symptoms.
疗效评估参数为:疤痕组织的色泽和硬度,疤痕的厚度和大小以及主观症状。
This paper highlights the experiment results in improving the toughness and hardness of white cast iron by heat treatment.
介绍了通过热处理提高白口铸铁硬度和韧性的试验结果。
Treated with laser the changes in microstructure and hardness of cylinder sleeve of oil-well pump for 45 steel were studied.
本文研究了45钢抽油泵缸套激光热处理后的显微组织和硬度的变化。
The chemical composition, microstructure, fracture morphology and hardness of cracked S45C steel parts were tested and analyzed.
对淬火开裂的S45 C钢零件进行了化学成分、金相组织、断口分析及硬度检测。
The effects of solid-solution temperature and holding time on the grain growth and hardness of GH4169 superalloy were investigated.
研究了热处理温度和保温时间对GH4169合金晶粒长大规律和硬度的影响。
The influence of RE on the microstructure and hardness of welded joint was studied by the experiments adding RE in electrode covering.
通过在药皮中添加稀土合金的试验,研究了稀土对高钒焊条焊补铸铁接头组织与硬度的影响。
However, the further increase in detonation frequency and gas-flow rates caused structure worsening and hardness declining of the coat.
但是当爆炸频率和气体流量进一步升高时,涂层的组织反而恶化,硬度降低。
The experimental results show that the depositing power and time have a certain effect on the depth and hardness of the deposited layer.
研究结果表明,电火花沉积功率和沉积时间对电火花沉积层的厚度和硬度有一定的影响;
The experiments consisted of the measurement of yield stress, tensile strength and hardness for samples cut from various parts of the forging.
试验包括对取自不同锻造零件的试块的屈服强度、抗拉强度及硬度的测量。
However, it is difficult for a kind of material to have high toughness and hardness on actual condition, so compounding casting often is used.
但一种材料同时具有高韧性和高硬度这两种性能在实际生产中是非常难以达到的,为此采用复合铸造工艺进行生产。
The hardening case depth and hardness curve can be changed by adjusting heating time, heating power and cooling speed during induction hardening.
在感应淬火中,通过改变加热时间、加热功率和冷却速度可以改变淬硬层深度和硬度梯度。
The composition, microstructure, and hardness of the ceramal layer were analysed with the help of EPMA, XRD and a microhardness measuring instrument.
借助EPMA,XRD和显微硬度计测定了熔覆涂层的化学成份、显微组织和显微硬度。
The influences of multilayer cladding on the microstructure and hardness of laser-clad layers were studied by metallographic microscope and hardometer.
采用金相显微镜和硬度计研究了多层熔覆对激光熔覆层微观组织和硬度的影响。
应用推荐