The Fe-Al coating sprayed by gas detonation-gun has a good property of resistant-corrosion.
采用气体爆燃喷涂技术制备的铁铝涂层具有良好的耐蚀性能。
Through microscopic observation and calculation of fractal dimension the seal coating failure of Al-Si.
通过微观观察及分形维数计算结果分析聚苯酯铝硅封严涂层失效原因。
Study of microstructure of the Fe-Al coating could provide dependable evidence for the research on resistant-corrosion.
对该涂层的微观结构进行分析，能够为涂层的耐蚀性能研究提供可靠的实验依据。
This article expounds Al coating technology and parameter chosce by analysing the oxyacetylene heat Al coating of iron frying Pan.
提出了氧乙炔焰铝丝喷涂普碳钢灼勺工艺及适宜喷涂参数。
The thermal stress in magnetron sputtered al coating on uranium substrate was studied by thermal elastic plastic finite element method (FEM).
对铀表面磁控溅射沉积铝镀层的热应力进行了热弹塑性有限元分析。
It was proved that high velocity arc spraying Ni-Al coating is one of best intermediate coatings with high adhesive strength and fine structure.
高速电弧喷涂镍铝涂层结合强度高，涂层组织致密，是优良的打底涂层。
The oxidation kinetics curve was drawn. The surface morphology and cross section micrograph of the Al-Si coating were studied by using SEM.
绘制了氧化动力学曲线，用带能谱分析的扫描电镜观察了涂层的表面氧化形貌和横截面组织形貌。
The result suggests that the coating of Al-based cored wire prepared by arc spraying has excellent high-temperature oxidation resistance and corrosion resistance.
研究结果表明：电弧喷涂铝基粉芯丝材制备的涂层具有优良的抗高温氧化和耐腐蚀性能。
In general, the fluorocarbon protecting coating could be well applied for the anodising insulation protection of Al alloy.
氟碳丙烯酸保护涂料能够满足铝合金阳极化绝缘保护的要求。
However, there is no study on the fabricating Al diffusion coating in a dynamics environment yet.
然而，在动态的反应环境中在镁表面制备铝扩散涂层的研究并未见报道。
Applications of auxiliary processes, in terms of abrading, polishing, wax finishing, sealant coating, paint spraying, wax spraying and et al, in coating automobiles are reviewed.
综述了打磨、抛光、打蜡、涂密封胶、喷涂涂料、涂保护蜡等辅助工序在汽车涂装中的应用。
Ta coating was prepared by plasma spraying, which composition and morphology were investigated using SEM, also the bonding strength between Ta coating and Al substrate was tested.
采用等离子喷涂法制备了钽金属涂层，用电子显微镜分析了不同工艺条件下钽涂层的化学成分、表面形貌，测试了涂层与基材的结合强度。
Spraying processes of hydraulic pressure oil tanks are discussed in terms of coating performance, coating process and et al.
从涂层性能、涂装工艺等方面讨论了液压油缸的喷涂工艺。
The basic contents of quality control in coating process, basic requirements for coating inspector, technical training and et al are introduced.
介绍了涂装质量检查的基本工作，涂装检查人员的基本工作要求和技术培训等。
The coating procedure thereof is described in terms of the material selection, substrate treatment, stain primer, binding primer, surface primer, finishing and et al.
分别对材料选择、底材处理、底着色、涂一道底漆、涂二道底漆、面修色、涂面漆工艺进行了处理。
The EIS characteristics of an anodic type anticorrosion coating prepared with Al-Mg alloy were studied.
利用电化学交流阻抗方法研究了铝镁阳极型强屏蔽涂层的电化学阻抗谱特征。
The bubbling, flaking, loss of wet adhesion and et al of the coating film occurred under the action of hot water, dissolved oxygen, corrosive chlorium and et al are introduced.
针对水箱中高湿热腐蚀环境，介绍了涂层在热水、溶解氧及腐蚀性氯离子等影响因素作用下发生的鼓泡、脱落、湿附着力丧失等现象。
The ion coating equipment and the technical experiment results for ion coating Al on uranium are described in this paper.
本文介绍了铀上离子镀铝使用的离子镀装置及离子镀工艺实验的主要结果。
HY-200 process procedure for colour chemical conversion coating of al and its alloys parts and the test method for quality control are introduced in this paper.
本文介绍了对铝及铝合金零件进行彩色化学转化处理的HY—200法的工艺及质量控制的试验方法。
The influence of al ion and Fluorine ion in phosphating process on phosphate coating quality was mainly discussed.
重点探讨了化成工序中铝离子及氟离子对磷化膜质量的影响程度。
The preparation of Al, Si and other elements co-diffusion coating and the mechanism of its high-temperature corrosion resistance were went into details.
对渗铝及硅和其它元素的共渗层的制备工艺及其抗高温腐蚀机理进行了详细讨论。
The influence of the epoxy resin, curing agent, pigments and fillers, solvents, additives, thickness of the coating film and et al on the performances thereof is discussed.
讨论了环氧树脂、固化剂、颜填料、溶剂、助剂、涂膜厚度等对涂膜性能的影响。
The white corrosion products on hot dip Zn al alloy coating exposed to seawater in dynamic aerated immersion were investigated by means of XRD and TEM.
采用XRD和TEM对热浸锌铝合金镀层在动态充气海水全浸试验时所形成的白色腐蚀产物进行了研究。
Plasma enhance electro-chemic al surface ceramic-coating (Microarc oxidation) is a new technique, which can in-situ form the ceramic coatings on the surfaces of some non-ferrous metals.
等离子体增强电化学表面陶瓷化(微弧氧化)是一项在有色金属表面原位生长陶瓷膜的新技术。
Plasma enhance electro-chemic al surface ceramic-coating (Microarc oxidation) is a new technique, which can in-situ form the ceramic coatings on the surfaces of some non-ferrous metals.
等离子体增强电化学表面陶瓷化(微弧氧化)是一项在有色金属表面原位生长陶瓷膜的新技术。
应用推荐