At the same time the matters needing attention in adhesive process and remedial measures for ports' breakage are pointed out.
指出管材在粘接过程中应注意的问题以及接口损坏时应采取的补救办法。
The method and adhesive process for Sodium-Naphthalene solution activating Polytetrafluorethylene (PTFE) surface were described, and the properties of adhesive were tested.
叙述了钠—萘溶液活化聚四氟乙烯表面的方法和粘接工艺，并测试了粘接件的主要性能。
Shaving board adhesive consists of mixed modified waste liquid and UF resins. Proper process can make the shaving board be of suitable strength and property density.
改性的麻杆黑液与自制脲醛树脂按一定比例调配作为刨花板粘合剂，选择适当的工艺条件，将麻芯与刨花的混合料压制成具有一定强度、适当密度值的板材。
The bonding strength is ensured by the correct choice of substrate material, surface preparation, adhesive and process parameter.
粘合强度可以通过选择正确的基体材料、表面处理、胶粘剂和工艺参数得以保证。
The effects of adhesive formulation and process conditions upon the performance of modified corn starch adhesive were explored in this study.
本论文主要研究了改性玉米淀粉胶粘剂的主要成分配比及工艺条件对产品性能的影响。
Two-component polyurethane adhesive for composite membrane was studied in terms of its composition, synthesis and process conditions.
本文确定了复合膜用双组份聚氨酯胶粘剂的组成成份，合成方法和工艺条件。
Reaction mechanism, technological process, and formulation of a cheap starch and urea-formaldehyde compound adhesive for saw-dust and shaving boards are mainly described in this paper.
本文着重介绍了锯末刨花板用价廉物美的淀粉脲醛复合粘合剂制作的反应机理、工艺流程及配方等。
During the integrated circuit packing process, the quality and service life of integrated circuit are decided directly by the quality of conductive adhesive through non-oxidation thermal curing.
在集成电路封装工艺过程中，对导电胶进行无氧化加热固化的质量直接决定了集成电路的质量和使用寿命。
The ideal formula of the adhesive is determined by series of experiments and the reaction process and thermal stability of copper foil adhesives are studied by te, TGA and DTA.
通过一系列研究确定了胶粘剂的理想配方，并通过红外光谱、热失重和差热分析法对其铜箔胶粘剂的反应过程和热稳定性进行了探讨。
The wear mechanisms during dry sliding process are oxidation wear and adhesive wear.
在干滑动摩擦过程中，磨损机制主要为氧化磨损和粘着磨损。
The development process and technical keys of PU hot melt adhesive interlining were introduced.
介绍了PU热熔胶衬布的研制过程和技术关键。
The adhesive prepared with this process has low cost and good fluidity and stable viscosity and high drying speed.
此工艺制备的胶粘剂成本低、流动性好、粘度稳定、干燥快。
Manufacture process and influence factors of one-component polyurethane adhesive for cork products were described in detail.
详细地阐述了软木制品用单组分聚氨酯胶黏剂的制备工艺和反应过程中的影响因素。
For a given layered planar structure, we use the solidifying process of the adhesive layer to simulate the change process of interface strength of the adhesive joint.
对于给定的层状平面结构，将粘接层的固化过程用于模拟粘接层界面强度的变化过程。
The process of wear was from adhesive to abrasive, the gold plating was worn out at last.
磨损过程为先粘结再擦伤，最后镀金层被磨穿。
Compared to traditional process, 25% of adhesive can be reduced and the drying time is short.
较传统工艺减少25%粘合剂，干燥时间缩短。
Mainly describe the properties of SMT adhesive, application method of various process and defects appearing in use and countermeasure. Also briefly analyzes future trend of adhesive.
主要介绍贴片胶的特性、在各种工艺下的使用方法及其使用中出现的不良现象与对策等内容，并简要分析了贴片胶的未来发展趋势。
Process for the preparation of coating, coated substrate, adhesive, film or sheet, for the thus obtained products and the coating mixture to be used in the process.
涂层、涂覆底材、粘合剂、薄膜或片材的制备方法，由该方法获得的产品，以及用在该方法中的涂料混合物。
Expansion extrusion molding, extrusion molding apparatus therefor, and process for producing pressure-sensitive adhesive sheet.
膨胀挤出模塑，采用该法的挤出模塑装置，及用于制备压敏粘合剂片材的方法。
The wear rate initially increases and then decreases with sliding distance increasing in all tested materials, wear mechanism during dry sliding process is oxidation wear and adhesive wear.
干滑动摩擦磨损率随磨损滑移距离的增加先增加而后逐渐降低，磨损机制主要为粘着磨损和氧化磨损。
Modifier was added on medium-term of synthetic process with its adding amount being 3%, a favourable low toxic modified UF resin adhesive could be synthesized on the basis of colloid theory.
应用胶体理论，在树脂合成过程中期加入改性剂，改性剂添加量为3%，合成了性能良好的低毒改性脲醛树脂胶。
The article explains the design, applications and production process of the architectural chloroprene rubber adhesive.
叙述了氯丁橡胶胶粘剂在建筑业的应用以及它的配方设计和制备方法。
Our good production environment and unique drying process overcome the defect of adhesive pieces.
我公司良好的生产环境和独特的干燥工艺，克服玻片易粘片的现象。
The paper introduces the formula, process and tensile strength of the organic-inorganic composite adhesive which is prepared by mixing acetalization of polyvinyl alcohol with silicasol.
叙述了以聚乙烯醇为原料，经缩醛化后和硅溶胶制备有机—无机复合粘合剂。介绍了配方、制备程序和拉伸粘结强度的试验结果。
Design and process of the extruder for hot-melt adhesive sheets were described briefly; extrusion technology was introduced itt details; and several determinant factors were discussed.
本文简述了热熔胶片成影机的设计加工，较详细地介绍了热熔胶片的成形工艺；同时，讨论了影响热熔胶片性能的一些因素。
The influences of surface treatments, the pressures during bonding process and the thickness of adhesive layer on shearing strength were investigated with epoxy resin-DDS curing system as adhesive.
采用环氧树脂-DDS固化体系作为胶接剂，探讨了各种金属表面处理方法、胶接时对胶接面施加的压力、胶层厚度等因素对胶接剪切强度的影响。
The unwinding wheel is arch design, and wipes out the wrinkling of adhesive tape in the process of feeding.
展开轮为独特的弓形设计，彻底消除胶带在送料过程中起皱现象。
Attempts continued into the 20th century, when Norwegian scientists tried applying a gelatine-based adhesive that shrank when it dried, peeling the scrolls' layers apart in the process.
进入20世纪，尝试依旧继续。挪威科学家采用明胶为主的粘合剂，想在轴卷干燥收缩的过程中一层层剥落。
On the base of establish oxidation process of corn starch, the preparation of corn starch adhesive was studied.
在确定氧化工艺的基础上，研究了淀粉胶粘剂的制备工艺。
The application prospect and process of RTV CR adhesive were related.
简述室温硫化氯丁橡胶胶粘剂的应用前景及工艺路线。
应用推荐