Finally add a subtle Outer Glow using black at 15% opacity to give a slight shadow to the content area.
最后添加一个外发光，黑色的15%透明度的，于是一个淡淡的内容区的阴影就这样出现了。
Double click on the rectangle’s layer and add an 8px white stroke. Change the Blend Mode to Overlay and drop the opacity to 30% to give a cool transparent effect.
双击圆角矩形图层然后添加8白色描边，宽度为8px，混合模式为叠加然后调整透明度为30%，这样就会有一个很酷的透明效果-_
Double click on the rectangle's layer and add an 8px white stroke. Change the Blend Mode to Overlay and drop the opacity to 30% to give a cool transparent effect.
双击圆角矩形图层然后添加8白色描边，宽度为8px，混合模式为叠加然后调整透明度为30%，这样就会有一个很酷的透明效果- _。
Add the following layer styles to the front part of the folder. Lower opacity to 90%.
为文件夹前面的部分添加下图所示的图层样式。不透明的设为90%。
Create new layer above the ribbon. Paint black using soft brush with low Opacity to add depth onto the ribbon.
创建新层以上剪彩。涂料用低透明度黑色软刷上添加功能区的深度。
Now you just need to take your 3 shadow elements and take them through the process outlined above to blur, add noise and alter their opacity correctly.
现在你只需要把你的3个阴影元素放到合成中并添加噪声、恰当的设置他们的透明度。
Add the following layer styles to the Paper. Lower the opacity of the layer to around 90-95%.
为纸片添加如下的图层样式。不透明度降至90- 95%左右。
Change the blend mode to Soft light on this layer, and then lower the opacity to around 38%. Now add the following blending options to your highlight layer.
在该图层上混合模式更改为柔光，然后不透明度降低至约38%。现在向您高光图层添加下列混合选项。
Now alter the opacities of these three layer to something between about 20% and 35%, just until they look right and don't do them all the same opacity, make them different and it will add some depth.
现在改变混浊这三个层之间有大约20 %和35 %，公正，直到他们期待的权利，不这样做他们都同样不透明，使他们不同的，这将增加一些深度。
Another trick I like to use often, is to add another layer on top of everything and paint the general colors I want in each part of the image, then set it to soft-light and lower it's opacity.
另一个我常使用的窍门是给在最顶层添加一层，并在我希望的位置进行绘制，然后设置它的叠加方式为柔光，并降低它的透明度。
Add another layer and repeat the same techniques as the last step, but this time make the brush color white and the layer opacity around 5%.
又增加了一层和重复同样的技术，作为最后一步，但是这一次使刷颜色白色和不透明层约5 %。
Add another layer of fabrics, adjust the opacity of both layers, add more coverage to high lights and surfaces looked at from a sharp Angle, and define the outline with brighter lines.
添加其他面料图层，调整两个图层的透明度，在从一个小角度看到的表面增加更多的覆盖高光，并确定明亮的细线条轮廓。
Add a shadow using the ellipse tool (u). Draw an ellipse as shown and add a slight motion blur. Reduce the opacity to your liking.
用椭圆工具(U)添加一个阴影。如下图所示绘制一个椭圆并添加一点点动感模糊。降低不透明度直到你觉得合适了。
Add a shadow using the ellipse tool (u). Draw an ellipse as shown and add a slight motion blur. Reduce the opacity to your liking.
用椭圆工具(U)添加一个阴影。如下图所示绘制一个椭圆并添加一点点动感模糊。降低不透明度直到你觉得合适了。
应用推荐