You will have three Ethernet adapters.
有三个以太网适配器。
The adapters now have ICONS on the pallet.
适配器现在在托盘上具有图标。
Each of the four adapters has two FC ports.
每个适配器都有两个FC端口。
Step 2: Create virtual adapters on the ivm.
步骤2：在IVM上创建虚拟适配器。
This concludes our introduction to adapters.
这就是有关适配器的介绍。
Some adapters have many configurable options.
某些适配器具有多个可配置的选项。
These are also known as Qlogic 2342 adapters.
它也称为Qlogic 2342适配器。
Instead, connectors and protocol adapters are used.
而是使用连接器和协议适配器。
Provide adapters that implement the common interface.
提供实现公共接口的适配器。
TCP/IP-supported LAN adapters connected to the network
连接网络的支持TCP/IP 的LAN适配器
These virtual adapters are used as the control channel.
这些虚拟适配器用作控制通道。
Both CICS and IMS have two versions of resource adapters.
CICS和IMS都有两个版本的资源适配器。
The AIX hosts were all using dedicated FC adapters (HBAs).
这些AIX主机均使用了专用的FC适配器(HBA)。
Communication interfaces: Token ring or Ethernet adapters.
通信接口：令牌环网或以太网适配器。
First of all we are increasing the variety of our adapters.
首先，我们正在增加适配器的种类。
One of the adapters is the boot adapter, not used for HACMP.
其中一个适配器是启动适配器，并非用于 HACMP。
WWPNs for all FC adapters on all VIOS involved in the migration.
在迁移所涉及的所有VIOS上的所有FC适配器的 WWPN。
For common integrations, IBM has introduced two sets of adapters.
对于一般的集成任务，IBM引入了两组适配器。
Typically, the requestors and providers are connected via adapters.
通常，请求者和提供者经适配器连接。
This will include some specifics on the protocol adapters to be used.
这将包括一些有关所使用的协议适配器的具体细节。
This defines the boot IP addresses on the respective network adapters.
这在网络适配器上分别定义相应的引导IP地址。
Thus, specific adapters are associated to specific logical partitions.
因此，特定的适配器将关联于特定的逻辑分区。
Checking there are no dedicated physical adapters assigned to the LPAR.
确认没有给这个LPAR分配专用的物理适配器。
Resource adapters are bundled into Resource Adapter Archive (RAR) files.
将资源适配器绑定到资源适配器存档 (RAR)文件。
Virtual disk, tape, CD or DVD and communications adapters are supported.
支持虚拟磁盘、磁带、CD或DVD以及通信适配器。
The Ethernet adapters themselves are created and configured using the HMC.
以太网适配器本身通过使用HMC创建和配置。
Step 2 should be done on all the FC adapters from which the disk has paths.
应该在有到目标磁盘的路径的所有FC适配器上执行步骤2。
Modify the LPARs properties to map the new virtual adapters to LPAR adapters.
通过修改lpar属性把新的虚拟适配器分配给lpar适配器。
For more details, see the information about adapters in the resources section.
有关详细信息，请参见“参考资料”部分中有关适配器的信息。
There are two additional ways to activate tracing for optimized local adapters.
有两种其他方式来为优化的本地适配器激活跟踪。
应用推荐