变速箱零件的配合面、压缩机零件的平面、轴端面等。
Transmission component mating plane, compressor component plane, and shaft ends.
轿车车身尾灯区与周边零件的配合间隙和高度差体现了整车的设计水平和制造装配水平。
Clearances and differences in height between rear lamp area of car bodies and ambient components represent the level of vehicle design and assembling.
表面粗糙度与机械零件的配合性质、耐磨性、工作精度、抗腐蚀性有着密切的关系，它影响到机器或仪器的可靠性和使用寿命。
The surface roughness directly influences the conformity, wear resistance, corrosion resistance, working accuracy of the machine, and the reliability of the instrument and its service life.
正确安装五金零件，正确穿上合适的密封胶条，保证胶条与型材胶条槽配合合适，发现损坏应及时更换。
Install the hardware parts and sealing strips correctly, the sealing strips and slots must match perfectly. Remember to replace the damages in time.
它是配合零件之间最小的预期间隙空间，代表着允许的最紧配合条件。
It is the minimum clearance space intended between mating parts and represents the condition of tightest permissible fit.
大规模生产中配合零件必须能互换，单向公差是经常遇到的。
In mass production, where mating parts must be interchangeable, unilateral tolerances are customary.
给出配合偶件的工作要求，据此设计偶件的配合精度和适用的装配方法，以及相应的零件加工精。
Based on the working demands of mate parts, this paper designs the mate precision of mate parts, suitable assembly method and the working precision of corresponding parts.
装配模型的结构体现了自项向下的设计理念，实现了装配树层次信息、配合信息和零件信息的分别管理。
The model embodied the top-down design idea, achieved the respective management of assembly architecture information, mate information and parts information.
适用于成批或大量生产，配合零件数少，装配精度较高的场合。
Suitable for batch or mass production, with fewer parts and high assembly accuracy.
现今的汽车市场依赖的是汽车制造商和零件供应商的紧密配合。
Samsung sees their partnership, SB LiMotive, as crucial since the car business relies on close ties between carmakers and their suppliers.
鼓式制动比盘式制动的零件多，维护也更困难，但鼓式制动造价便宜，且易于与紧急制动机构配合。
Drum brakes have more parts than disc brakes and harder to service, but they are less expensive to manufacture, and they easily incorporate an emergency brake mechanism.
本文以质量损失函数为计算基础，得出零件非配合尺寸的容差计算公式。
Using Genichi·Taguchi′s approach, this paper gives all formulas that are suited for calculating the allowances of mechanical parts′ non-fit measurements.
“小范围装配”包括零件配合的基本工程模型，以及对遥轴顺应性装置的解释。
"Assembly in the small" includes basic engineering models of part mating, and an explanation of the Remote Center Compliance.
选定配合副中一个零件制造成多种尺寸作为调整件，装配时利用它来调整到装配允许的偏差；
With a pair of selected parts to various sizes as the adjusting piece, use it to adjust the assembly deviation to permit assembly;
零件之间的接触与配合问题在内燃机零件强度和可靠性设计中是一个迫切需要解决的重要问题。
The contact and fitting between the engine parts are exigent problems in the design of intensity and reliability.
零件间配合精度和配合面贴合度的要求也提高了。
Accuracy of components, and the fit with the requirements to improve the surface.
适用于成批或大量生产，配合零件数少，装配精度较高的场合。
This method has the advantages of convenient operation, easy to control, high production efficiency, easy to organize production, but the processing precision of parts requiring high.
在过盈配合中由于配合表面过盈量的影响，常使装配后的套筒类零件发生轴类零件内径减小和孔套类零件外径增大。
In the interference fit of assembled parts, inner diameter of sleeve-type parts was reduced and outer diameter of whole cover parts was increased by the magnitude of interference effects.
定制的装置与设备配合，它可以是薄片，封装零件，或连接器的模块，都能安装到RI接头上。
Custom fixtures adapt the devices, which can be wafer, packaged parts, or connectorized modules, to the RI universal interface.
该方法操作方便，易于掌握，生产效率高，便于组织流水作业，但对零件的加工精度要求较高。适用于配合零件数较少、批量较大的场合。
This method has the advantages of convenient operation, easy to control, high production efficiency, easy to organize production, but the processing precision of parts requiring high.
零件上的花键孔与传动轴端部的花键轴相配合，用于传递动力之用。
Parts of the spline hole and the shaft end of the spline shaft of it, for power transmission purposes.
在精加工以内孔为定位基准的零件时，所用芯轴类工装如果采用间隙配合定位，由于定位间隙的存在，必然影响零件的加工精度。
When machining parts with bore as positioning reference, if clearance fit positioning is adopted, machining accuracy is certainly affected due to the existence of clearance.
解决现有拉马难以拆卸一些配合较紧的轴上紧固零件的问题。
The invention solves the problem that the existing screw extractor is hard to disassemble some shaft fastening pieces with tight fitness.
解决现有拉马难以拆卸一些配合较紧的轴上紧固零件的问题。
The invention solves the problem that the existing screw extractor is hard to disassemble some shaft fastening pieces with tight fitness.
应用推荐