对监测系统监测流量与IS-25型旋浆式流速仪实测流量进行精度分析。
The analysis on the accuracy is made for measuring flow with monitoring system or with IS-25 flow velocity meter.
对近景摄影测量检测大型匀矿机变形进行了介绍和讨论，并对该方法进行精度分析。
The detection of deformation for big mineral machines has been introduced and discussed by using close- range photograph.
给出了测时差定位系统具体的定位公式，并对二维目标定位问题进行精度分析、推导，并提出最优布站原则。
This paper gives some formulas for TOA difference location system, analyzes the accuracy of 2D target location and provides the optimal distribution principle by derivation.
基线解算是静态GPS测量中的关键步骤，对各种情况下基线解算的结果进行精度分析有利于根据观测条件改善GPS测量精度。
Baseline solution is the key step of static GPS surveying. The precision analysis of baseline solution result under every condition is benefit to improving GPS survey precision.
因此，文中提出一种基于能量中心匹配的缺陷深度定位技术，并通过设置人工缺陷进行精度分析，结果表明该算法能达到很高的定位精度。
So a kind of depth location technique based on energy center matching is proposed and precision analysis is carried out to verify that the algorithm provided i…
为了提高分析精度，我们在很低的以年度为时间尺度的规模上进行了一系列的相关分析。
To refine the analysis, a series of correlation analyses were carried out at the much lower scale of an annual level timeframe.
这里主要运用不同的灰色系统理论模型对实验数据进行拟合，误差分析显示精度是很高的。
Here different grey system theoretical models are used to fit the experiment data; the error analysis demonstrates that the precision is high.
该文利用平面正四边形阵列对直升机目标进行定位，讨论了定位系统的原理及其算法，并对定位精度进行了分析。
This paper USES a square array to locate a target of helicopter and deals with location theory and its algorithm, as well as analyzing location accuracy.
精度分析和实际应用表明；观测成果是可靠的，采用几种精密测量方法联合进行，可以满足观测标志的高精度要求。
The precision analysis and practical application indicate that all the results are reliable and united several precision surveying methods can satisfy high accuracy.
文中论述了装定区的选择、提出了装定窗口的概念，并对系统精度和误码率进行了分析和初步研究。
The dissertation discusses the choosing of the setting area and gives the concept of the setting window, and analyzes and researches the system precision and the rate of error code.
实际运行结果表明：利用聚类分析法进行负荷短期预测，短期负荷预测的精度大大提高。
Practical operation results show that the cluster analysis method can considerably improve the accuracy of short-term load forecasting.
因此，建议在实际工程中可用一年左右的试验数据确定的徐变特性参数来对结构进行分析和计算，就可保证足够的精度和准确性。
Therefore, it is proposed that creep parameters determined by test data in one year are adopted in practical engineering to assure a good precision in analysis and calculation of structures.
本文主要就采用这一方法测光速时，对影响测量精度的主要因素进行了分析。
This paper mainly on the speed meter of this approach, the main factors affecting measurement accuracy are analyzed.
利用软测量的思想，采用神经网络建立软测量模型和小波分析进行数据处理，以克服传统方法的不足，提高出口带钢厚度预测的精度。
The idea of soft-measurement is used in our work and neural network and wavelet transform are adopted to overcome deficiency of traditional method and improve forecast accuracy of exit thickness.
深入分析了引起系统测量误差的原因，并利用神经网络对线结构光测量系统进行误差补偿，提高了系统的测量精度。
The reason that caused measurement error is analyzed deeply. The paper makes use of the neural network to compensate linear structured light measurement system, so improve the measurement precision.
通过实测数据并用谐波分析的方法对两项误差进行补偿与调整，提高了感应同步器的测角精度。
By applying the harmonic analysis method to adjusting and compensating, the practical test data is acquired, and the inductosyn Angle measuring accuracy is, raised.
对基于SLS技术的精密铸造过程中的精度控制进行了研究分析，并提出了解决办法。
The precision controls during investing casting process based on SLS are researched and analyzed, and some means to solve the precision problems are put forward.
介绍了天文找北系统的结构和工作原理，对找北系统的精度进行了分析。
The structure and principle of the north-finder is discussed, and the precision of the north-finder is analyzed.
并对跟踪精度进行了分析。
选用过程仪表校验仪器必须对其可靠性、精度、溯源性、维修、环境条件进行综合分析，做出合理的选择。
Before choosing the calibrater, you must synthetically analyse the uncartainty, the accuracy, the traceability, the maintain, the environment of the calibrater and make the reasonable selection.
并对系统最大误差位置进行误差参数灵敏度分析。用蒙特卡洛法进行精度综合。
The sensitivities of error parameters were analyzed at the maximum error position, and accuracy synthesis was conducted by using Monte Carlo method.
针对实验室现有的设备，分别对单点定位误差和区域定位误差进行试验、分析，对不同GPS使用精度进行比较。
Based on the facility the lab owned, we analyze single error and region error and compare different GPS precision.
利用误差传递公式，对红外密集度立靶的测量精度进行了分析。
The error transfer formula is used to analyze accuracy of infrared photoelectric target.
最后，对本装置的测试精度进行了检验并对检验结果进行了分析。
Finally, test precision is made by experiments and the results is also analyzed.
同时对该方法的精度与误差进行了分析。
同时对该方法的精度与误差进行了分析。
应用推荐