文章主要叙述了机械手的设计计算过程。
The paper mainly narrated the design and calculation of light and transfer manipulator.
介绍了供热水装置的设计计算及安装方法。
The design calculation of hot water supply device and its installation were described in this paper.
负责和销售工程师合作取得客户的设计计算输入。
Be in charge of getting the input data from the customers with support of sales engineers.
通过算例介绍了同向双螺杆几何设计计算软件的功能。
The functions of the calculation software for a corotating twin screw geometry design are introduced by means of showing a calculation example.
所导出的数学表达式，可用于精确的数值分析和设计计算。
The mathematical formulation given can be used for accurate numerical computation and design purposes.
非标设备设计或细部设计知识。有热力学及风量设计计算基础。
Knowledge in mechanical design and detail design of non-standard equipment. Basic knowledge of thermodynamics, air volume calculation.
文章就国内关于膜结构设计计算方面的主要研究成果进行了综述。
This paper reviews the main research achievements of the design and computation of membrane structure in China.
并结合有关结构设计知识，提高分析和解决地基基础设计计算的能力。
Combined with the structural design knowledge to improve analysis and design of foundation settlement of the capacity.
首先，本文介绍了引射器的基本原理，对其基本结构进行了设计计算。
Firstly, the basic fundamental of ejector was introduced and its structure was designed and computed.
复杂桁架式结构的稳定性分析成为当代大型起重机结构设计计算的难点。
So the stability analysis of complicated lattice structure becomes the crux of contemporary and large cranes' structure design and its calculation.
提供了本体制应用价值的理论依据和工程设计计算、系统性能评价的方法。
The applicable value based on theory, computation of engineering design and estimation for systematic performances are also given.
详述了倒圆角工具主要零件的设计计算、技术要求和倒圆角工具的使用方法。
The design calculating, technical standard and the using method of the chamfered tool are details introduced.
试验与数值对比分析表明该方法合理有效，可作为桥梁加固的设计计算依据。
The results show that this method is rational and effective, it can provide a basis for bridge strengthening practice.
本文可为同类桥梁在设计计算中提供参考，并为钢桥规范的修订提供技术资料。
This text can offer reference in calculating of design for similar bridge and offer the technical data for criterion revision of steel bridge.
本文对修正对数螺线的理论模型进行了详细的分析，并给出了设计计算的方法。
In the paper, theoretical mode of revised logarithmic helical curve is discussed carefully, and the methods of calculation and design are also given.
为桩锚支护结构施工进程中受力变形的设计计算和过程控制提供了动态计算模型。
What we have done here provides developing calculation model for the force-deformation calculation and process control of PARS during construction.
对自动调整臂的设计计算作了详尽的分析，主要以下几个方面：1矩形截面力和弹簧的设计计算。
There are mostly a few aspects that fully analyse for design and compute for AIRA:1 design and compute for spring of rectangle section .
长期以来，制冷行业中换热设备的设计以传统的经验设计为主，主要依靠工程设计人员的手工设计计算。
For a long time, the heat-exchange equipments in thermal power system have been designing mainly depending on traditional experience and manual calculation.
经文献中的实验数据考核比较，本文所编制的设计计算系统具有较好的通用性，计算值偏差在士20%左右。
Tested by experimental data from literatures, the computed system built in this paper is proved to be of good commonality, and the computational mistake is around 20%.
并应用其对微灌工程实际项目进行设计，可以大大降低工程设计人员的设计计算量，具有重要的工程实用价值。
Thus, the engineering design personnel's design calculation quantity was greatly reduced and the important value of practical project was achieved.
本文对具有高承载能力的空气静压轴颈轴承进行了研究，给出了实验和计算结果。在设计计算上，对传统的计算方法做了修正。
This paper has investigated air hydrostatic bearings with high load carrying capacity and given experimental and calculating results. Traditional method is modified in design and calculation.
在一定的进气状态下，为达到要求的出气干度，对给定的空气流量进行了设计计算，以得到合适的传热面积与制冷系统的匹配。
At a given air inlet condition and airflow rate, meanwhile, dryness of air outlet was required, proper heat-transfer area and matching refrigeration system are obtained through calculating.
由于在焊缝部位存在焊接缺陷，采用传统的建立在构件无缺陷、无裂纹基础上的强度理论进行设计计算时，往往不能确保起重机在额定载荷下使用的安全性。
Since there are weld defects in welds, using traditional strength theory based on no defect and no crack to design, crane's security in rating load can't be insured.
介绍了SPDS- 120和SPDS - 114两种型号丢手工具的结构设计、工作原理，重点介绍了SPDS - 114型丢手工具的结构、特点及相关设计计算。
This paper introduced the structural design and working mechanism of SPDS-120 and SPDS - 114 releasing tools, especially the structure, characteristics and relevant design calculation of SPDS - 114.
香农展示了如何计算这个限度，这为设计压缩方法将最多的信息填入最小的空间开辟了道路。
Shannon showed how to calculate this limit, opening the way to the design of compression methods that cram maximum information into the minimum space.
有些决定，如壁厚和销轴直径，可能取决于科学的计算，但非科学的部分的设计仍然是首要的。
Some decisions, such as wall thickness and pin diameter, may depend on scientific calculations, but the nonscientific component of design remains primary.
该方法设计理论简单易懂，避免了状态方程和驱动方程的复杂计算。
The method is that designing theory is simpleness and being understood is easy and avoiding complexity computation on state equations and drive equations.
该方法设计理论简单易懂，避免了状态方程和驱动方程的复杂计算。
The method is that designing theory is simpleness and being understood is easy and avoiding complexity computation on state equations and drive equations.
应用推荐