文中着重论述了自适应心跳信息检测、软双工设计和背景数据同步，实现了应用软件的高可靠性。
It emphasizes adaptive heartbeat message detection, dual-software design and background data synchronization, and demonstrates how to apply the high-reliability system.
双工滤波器、均衡器、衰减器采用插件式设计。
Duplex filters equalizer and attenuator all adopted plug-in design.
本文以LC网络为例，提出了利用电路优化技术代替网络综合方法，设计高性能的双工器。
In this thesis, we use circuit optimization technique to replace the network synthesis theory and design high performance diplexers on the basis of LC network.
主要介绍该芯片的功能特点，并以该芯片为基础设计一种低成本的半双工无线数据传输模块。
This paper introduces its functions based on which gives the design of half-duplex wireless data transmission module.
本文介绍由双工器组成的通带毗邻多工器的结构及其设计方法。
The structures and their design methods of the multiplexers with contiguous pass bands consists of diplexer in this paper.
介绍了某车型片簧冲大孔、切边双工位模具设计要点及注意事项。
The key points in designing a two operating position punching and trimming die for shaping an automotive little leaf spring were discussed.
介绍了一种针对短距离通信的、半双工、低功耗无线话音通信器的实现方案。从硬件电路和软件设计进行了阐述。
A wireless digital semi-duplex low power voice transceiver for short-distance communication is introduced in terms of the design of its hardware and software.
在ISDN用户线基本接入全双工传输系统的设计中，线路编码是重要的一步。
Line coding is an important step in the design of full-duplex transmission system to support ISDN subscriber line basic access.
论文详细地论述了双工器的分析原理、设计步骤以及测量调试过程。
The design methods, simulation procedures and measurement results are described in detail in this paper.
给出了射频ic选取中需要注意的事项，详细地论述了无线半双工通信协议的设计过程和整个系统的电源管理。
Matters needing attention about the choice of the RF IC are given, and the wireless semi-duplex communication protocol and the whole system's power management are presented in detail.
使用准同步法，在一对usbISO端点上，成功地实现了实时全双工usb音频通信功能，简化了时钟同步系统的设计。
Using the plesiochronous communication model, implement duplex audio communication functions on twain USB ISO endpoints, simplify the design of clock synch system.
为达到以上目标，本论文致力于新型小型化波导滤波器及双工器的研究和设计。
The purpose of this thesis is to study and design new compact waveguide filters and diplexers with these characteristics.
为了避免机床这种一体式双工位测量和加工结构在工作时产生较大的误差，设计了双工位的校准装置，并对校准原理和校准过程进行介绍。
In order to reducee the errors brought out from the measuring and grinding works finished in one machine, a calibrating device is designed and the principle and the calibrating process are introduced.
本文介绍了利用VHDL语言设计出全双工异步接收发送器电路的方法，并通过计算机仿真和实验证明了设计的正确性。
In this paper, the design of full duplex UART base on VHDL is thoroughly discussed. And the exactitude of this design has been proved by means of computer simulation and experiment.
设计和组装了用于液相色谱的双工作电极电化学检测的薄层流通池和双恒电位控制器。
Dual-electrode thin-layer electrochemical cell and bipotentiostat controller were constructed for liquid chromatography withelectroch emical detection.
定义双工合约的程式设计模型是将各组合分隔到不同的介面中，并将属性套用至各个介面。
The programming model for defining a duplex contract is to split each set in a separate interface and apply attributes to each interface.
在电路结构设计部分，主要讨论了采用集总参数传输零点滤波器实现天线双工器和采用PIN管实现天线开关的设计方法。
The circuit design part mainly introduces the duplexer design with lumped apices filter, and the antenna switch design with PIN diode.
最后，设计了使用E面交叉耦合滤波器和E面多模腔滤波器的构成的紧凑结构毫米波双工器。
Finally, new, compact millimeter-wave diplexers which employ cross-coupled E-plane filters and E-plane filters with over-moded cavities are analysed.
最后，设计了使用E面交叉耦合滤波器和E面多模腔滤波器的构成的紧凑结构毫米波双工器。
Finally, new, compact millimeter-wave diplexers which employ cross-coupled E-plane filters and E-plane filters with over-moded cavities are analysed.
应用推荐