该调查没有计算误差幅度。
首先分析了标量衍射理论的能量计算误差。
The energy calculation error of scalar theory was investigated firstly.
首先介绍NFDTD，并分析其计算误差。
Firstly, the NFDTD is introduced and its numeric error is analyzed.
计算误差不超过4%。
为了消除这种计算误差，出现了有限元接触分析方法。
To avid this computational error, it comes forth finite contact elements analysis method.
利用本算法，图像面积和周长的计算误差最大不超过2 % 。
Using this algorithm, the computation error of image area and girth is less than 2 percents.
特别是低频段部分，因为谱线数太少，会造成更大的计算误差。
Especially, in the lower frequency bands, the bigger calculation errors arise because of the few spectrum points.
由于经验估算、考虑环境因素简单，由此带来较大的计算误差。
However, error can be caused because of empirical estimation and the simple consideration of the circumstance factors.
轴功率的计算误差随着转速的增加而增大，随着压力的增加而减小。
The calculation error in predicting brake power increases with increasing engine speed and decreases with increasing pressure.
但用弹性运动学模型来进行运动学模拟后发现，这个计算误差并不大。
However, elastic kinematics model to simulate the kinematic and found that this calculation error is not significant.
分析了影响燃气爆炸极限的因素以及燃气爆炸极限的计算方法和计算误差。
The factors affecting gas explosion limits, the calculation method and the calculation errors of gas explosion limits are analyzed.
定量地分析了成像处理器增益计算误差对SAR系统辐射定标精度的影响。
A quantitative conclusion on the contribution of imaging processor gain to SAR radiometric calibration error is obtained.
学习过程通过调整权值、计算误差、修正隐层单元的参数，以达到最优结果。
Through adjusting weight, computing error rate and modifying the parameters of hidden nodes, optimal results will be achieved in the learning procedure.
实际算例表明，本文算法不仅计算过程稳定、计算速度快，而且计算误差小。
The application examples have shown that this method is stable in calculation process, rapid in calculation speed and minimal in calculation error.
修正即便仅仅是一个计算误差或者是一个另外的观点事例能够简简单单地增加一点点分数。
Correcting even one calculation error or adding one other point or example can easily add a few points to your grade.
昨天发布的更新后软件(4.0.1)可以改进这个苹果几个星期前发现的信号计算误差。
The software update (4.0.1) released yesterday will take care of the error in the signal calculation algorithm that Apple discovered several weeks ago.
本文在旋转圆盘电极数据处理中，为避免增大计算误差，采用了新的计算方法。
A new calculation method was used in order to avoid increasing calculation error in the data processing of the rotating disc electrode.
在数值计算方面，本文采用了新的计算域，减小了由于边界条件造成的计算误差。
In numerical computation aspect, by implying new computational geometric field, computation error caused by boundary condition was decreased.
在一定条件下、最小范数解更能反映位移场的真实状态，并使计算误差分布均匀。
With this method. the situations of dis-placements and stresses may be shown more exactly and the calculus errors have a even distribution.
比较结果表明，除等效热降法外，热力学方法和汽轮机原理方法的计算误差都很大。
The result shows that the error of thermodynamics method and steam turbine theory method are very big except the equivalent enthalpy drop method.
对于某些具有宽圆盘(如离心机转鼓)的悬臂转子，这种近似会引起较大的计算误差。
For some overhung rotors of great-width disks, such as the rotor of the vertical centrifuge, this kind of approximation will cause larger calculating errors.
进行数值求解，通过数值解与精确解的比较，对计算误差的变化规律进行了分析研究。
By a comparison of the result with that of the analytical solution, the computational error of the numerical solution is discussed.
用程序计算器进行天然气流量计算，可减少人为的查表和计算误差，操作也十分简便。
The calculation of natural gas flowrate with a programmable calculator can reduce human errors from consulting tables and calculation and its operation is very convenient.
面形检测采用边缘定位的方法，并且结合了曲线拟合的方法求解一维位移场来计算误差。
It USES edge localization and curve fitting to solve one dimension displacement field and calculate the error.
在简易柔性悬索桥桥型几何模型分析的基础上，对主索张力及其计算误差进行分析研究。
Based on the analysis of the geometrical models in a simple flexible suspension bridge, the skyline tension and its errors in calculation were analyzed.
通过对相对偏心率简化计算误差的分析，提出腔内孔式回油静压轴承设计中的几点建议。
Several Suggestions on designing the hydrostatic bearings by using relative eccentric ratio to simplify the calculating error analysis have been proposed.
将试验结果与理论结果对比，理论计算误差在可接受的范围内，说明有限元建模比较合理。
Compared the experiment result with the theory analysis result, the error of the theory calculation is proved acceptable. The finite element modeling is validity.
计算关联式具有较高的精度，热力学参数计算误差小于1 %，迁移特性参数误差小于4%。
The calculation shows a high accuracy: the error is less than 1% in thermodynamic properties and 4% in thermophysical properties.
验证计算结果表明：解析公式与计算机数值计算法结果相比较，计算误差小，具有实用价值。
The results of verifying calculation show that the analytic formula has smaller computational error as compared with computer numerical arithmetic, and therefore it is practical.
验证计算结果表明：解析公式与计算机数值计算法结果相比较，计算误差小，具有实用价值。
The results of verifying calculation show that the analytic formula has smaller computational error as compared with computer numerical arithmetic, and therefore it is practical.
应用推荐