试映羊毛采用高纯石英制成，非常适用于进样口衬管。
Quartz Wool was made from high-purity quartz, extremely low in metallic oxide impurities.
采用高纯石英制成，非常适用于进样口衬管。
Quartz Wool - Made from high-purity quartz, extremely low in metallic oxide impurities.
红宝石的水热生长试验在密封贵金属衬管中进行。
An experiment on hydrothermal growth are in process in a sealed tube with a precious metal liner.
清洗进样口，如有必要，更换密封垫，衬管，隔垫。
Clean the injector port, replace critical injection port seals, replace injection port liners, and change septa as needed.
内接续管为热镀钢制件，外续管口及两端衬管为铝制件。
The inner sleeve is hot-dip galvanized steel, the outer sleeve and lining sleeves are aluminium.
本实用新型涉及一种用于套管通道修整及衬管加固磨鞋。
The utility model relates to a grind shoe for finishing sleeve tube paths and fixing lining tubes.
衬管悬挂器有许多尺寸和规格，以适应各种不同的完井条件。
Liner hangers are available in a range of sizes and specifications to suit a variety of completion conditions.
连接两节管子(生产油管、套管或衬管等)所用的带螺纹的连接件。
A threaded coupling used to join two lengths of pipe such as production tubing, casing or liner.
利用所研制的水平井软件HWCS对割缝衬管完井的产能进行了预测。
The software of HWCS developed by ourselves, has been used to predict the productivity of slotted liner well completion.
筛管和衬管的堵塞和腐蚀会损害整个完井系统的功能性，缩短油井寿命。
Like plugging, the corrosion of screens and liners compromises the functionality of the entire completion and shortens well life.
在储层段没有设置套管或衬管的完井。这种就使产出的流体直接流入井筒。
A well completion that has no casing or liner set across the reservoir formation, allowing the produced fluids to flow directly into the wellbore.
以石棉水泥砂浆离心管作为内模衬管，浇筑混凝土后构成现浇混凝土空心板。
With asbestos cement mortar pipe being used as inner liner, concrete is cast to form hollow slab.
针对割缝衬管完井方法，进行了完井参数、单根割缝衬管长度、完井管柱结构的优化设计。
For the well completion method by slotted liner, well completion parameters, single slotted liner length and pipe string structure in well completion are optimized.
带眼衬管一般用于小直径井筒或在不需对衬管注水泥(如层位封隔所要求)的储层内的侧钻。
Perforated liners typically are used in small-diameter wellbores or in sidetracks within the reservoir where there is no need for the liner to be cemented in place, as is required for zonal isolation.
另外，在没有安装任何套管或衬管的情况下，在储层段的选择性处理或补救作业则更为困难。
Also, without any casing or liner installed, selective treatments or remedial work within the reservoir section are more difficult.
衬管补贴工艺技术能实现对射孔井段、套损部位的有效补贴，延长油(水)井开发生产的周期。
The technology of liner subsidy is effectively done to perforated parts and destroyed casing which can prolong the period of the water and oil Wells for production.
在裸眼完井产能评价模型的基础上进一步推导出火山岩气藏射孔完井和割缝衬管完井产能评价模型。
Through the open hole completion productivity evaluation model, respectively derive perforated completion and slotted completion productivity evaluation models.
如果筛管和衬管发生了部分堵塞，产液流体则会转而流向设备中更开阔的地区，从而导致局部流速的增大。
Partial plugging of well screens and liners redirects the flow of produced fluids to open areas of the hardware with a resulting increase in the local inflow velocity.
针对有衬管结构的REAC管束失效案例，采用FLUENT数值模拟，得到了REAC管束的实际爆管原因；
FLUENT was applied to simulate liner pipes which had invalidation case , the actual reason of REAC pipes bursting was found;
本文研究气相色谱进样系统中，玻璃衬管中有、无 玻璃棉填充以及样品浓度的高低对仪器的重现性的影响。
The impact of repetition on Gas Chromatogram was studied with glass wool in glass injector insert and different concentration samples.
在套管或衬管与周围的水泥环之间所形成的小间隙，这些间隙是由于在固井期间或固井之后温度或压力的变化所致。
A small gap that can form between the casing or liner and the surrounding cement sheath, most commonly formed by variations in temperature or pressure during or after the cementing process.
对割缝衬管在防砂井中受外挤力作用进行了分析，计算了井底压力（包括流体流经砾石层和割缝衬管的压降） ，建立了衬管割缝参数与割缝条幅弯曲强度及刚度之间的关系式。
The pressure of slotted pipes in a sandy well was analyzed. The bottom hole pressure was computed. A model for computing the bending strength and stiffness of a slotted pipe was proposed.
管腔纵切面：单层立方上皮衬于管腔内。一些立方细胞之间的边界相当清晰明显。
Simple cuboidal epithelium lining a tubule (longitudinal cut). Some of the cell boundaries between "blocks" or "cubes" here are quite distinct.
介绍了避免无填料和衬芯的长矩形管弯曲成形后管壁出现内陷及折痕的工艺，模具结构特点及设计中注意的事项，模具结构合理，便于加工、装配及使用。
The technology to avoid the dishing and folding of pipe shell appearing at the bending of long rectangular non-stuffing and coreless tube was introduced.
在简介磨球、衬板磨损和失效的基础上，评述了国内外水泥工业管磨机所用磨球、衬板的常用材质。
Some general materials for the grinding balls and lining boards in ball mills of cement industry were reviewed.
埋入部分包括蜗壳座环、尾水锥管、尾水肘管、机坑里衬等。
The embedding part includes volute socket ring, tail water taper pipe, tail water ell, pit liner and so on.
提出用钒和铜混合基体改进剂衬钽管石墨炉原子吸收测定镓的方法。
A method for the determination of gallium by the tantalum foil-lined graphite furnace atomic absorption spectrometry with vanadium and copper as mixed matrix modifier has been investigated.
本文针对高锰钢衬板的损坏原因进行了分析，指出了锰钢材料作为衬板的不适应性，并对低碳低合金钢在管磨机上的试验使用情况作了介绍。
This results in large liner consumption. In this paper the abrasion reason of high-manganese steel liner is analyzed. The result indicates inapplicability of manganese steel to making liner.
生产电站锅炉喷燃器火嘴、中心筒、风帽、煤粉管、灰渣管、衬板等400多个规格型号的耐热、耐磨、耐腐蚀特种钢铸件。
The main products are all kinds of heat-resisting, abrasion-resisting and corrosion-resisting special steel and boiler mouth, coal-dust tube and so on, about 400 specifications.
生产电站锅炉喷燃器火嘴、中心筒、风帽、煤粉管、灰渣管、衬板等400多个规格型号的耐热、耐磨、耐腐蚀特种钢铸件。
The main products are all kinds of heat-resisting, abrasion-resisting and corrosion-resisting special steel and boiler mouth, coal-dust tube and so on, about 400 specifications.
应用推荐