通过为不锈钢表面提供一个氧化环境的化学处理，钝化膜可以得到增强。
The passive film may be augmented by chemical treatments that provide an oxidizing environment for the stainless steel surface.
研究了不同的样品表面处理方法对测定薄板钢样中氧的影响。
The influence of different surface treatment methods on determining oxygen in steel sheet has been studied.
钢的热处理工序包括硬化、回火、退火和表面硬化。
The procedures of heat treatment of steel include hardening tempering annealing and case hardening.
如果钢表面发生上述损坏，产生锈，用电力工具对表面进行清除，处理至二次表面处理等级，涂上一层与原始油漆一样的涂层。
When such damage comes to the surface of steel and rust occurs, the surface shall be cleaned by power tools to the secondary surface preparation grade and coated as originally painting scheme.
化学处理，例如重铬酸钠溶液，可以促进无氧化膜和杂质不锈钢表面的钝化膜更快速度的生成。
Chemical treatments, such as sodium dichromate solutions, may facilitate the more rapid formation of the passive film on a stainless steel surface already free of scale or foreign matter.
结果表明，该钢经复合处理后，具有较好的表面硬度和良好的耐磨性，显著地增加了刀具的使用寿命。
The results showed that the steel after combined treatment had higher surface hardness and wear resistance, and prolonged the service life of cutting tool.
针对热作模具钢的表面氧化处理，本文开发了一种带蒸汽预热装置的氧化处理炉，这种炉型现已应用于工业生产。
A furnace with preheating equipment for water vapor is developed for surface oxidation treatment of hot work dies. This type furnace is successfully used in industry.
钢表面清理是重要的涂装前处理工艺，适应性强，应用范围广，受到国内外普遍的重视。
The steel surface's clean is the important disposal technics before painting, adaptability strong, using widely, is regarded important home and abroad.
达克罗的应用范围很广，它不但可以处理钢、铁、铝及其合金，还可以处理烧结金属，以及特殊的表面处理。
Dacromet has a wide range of applications. it not only can be used to treat steel, iron, aluminum and its alloys, but also can handle sintered metal, and the special surface treatment.
采用AGA—782热像仪实际测定钢激光热处理表面温度场。
The actual surface temperature field during laser heat treatment has been measured by thermovision type AGA 782.
本文主要介绍中碳合金结构钢经整体塑性变形、热处理后再进行表面冷变形工艺是提高材料疲劳强度的有效途径。
This paper mainly presents that constructional mid-carbon alloy steel, after bulk moulding deformation, heat treatment and cold surface deformation can raise fatigue strength of materials effectively.
等离子处理也能改变其它材料的表面化学(表面性质)，如硅、不锈钢及玻璃。
Plasma treatment can also change the surface chemistry (and thus surface properties) of other materials, such as silicon, stainless steel, and glass.
磨削强化技术是一种集磨削加工与表面淬火于一体的新技术，可对钢件表层进行强化处理。
The grinding strengthen technology is a new process engineering of surface heat-treatment, which USES a mass of grind heat produced in grinding process to handle workpiece materials.
低温离子渗碳处理是一种能改善奥氏体不锈钢表面力学性能的有效方法。
After low temperature plasma carburizing, the surface hardness, wear resistance and fatigue capability of austenitic stainless steels are largely increased.
热处理：钢及有色金属的常规热处理与化学热处理，钢的淬透性测试，钢的表面处理等。
Heat processing: normal heat treating and chemical heat treating of steel and nonferrous metal; testing the hardenability of steel; surface treatment of steel.
通过铸造表面合金化和复合变质处理，使中锰奥氏体钢的强度、韧性和表面硬度显著提高。
The strength, toughness and surface hardness of medium Manganese austenitic steel have been increased greatly by casting surface alloying and complex modification.
针对钢球表面易产生擦伤，影响钢球精度等原因，采用表面强化处理的方式提高钢球表面质量，降低振动值，提高疲劳寿命。
Based on this, the steel ball surface quality is increased by the means of surface handling, then the vibration value is reduced, the fatigue life is raised.
制备表面抗菌不锈钢的方法有化学热处理、磁控溅射、离子注入、溶胶-凝胶和化学沉积。
There are various methods to obtain antibacterial surface on stainless steels, such as chemical heat treatment, magnetron sputtering, ion implantation, Sol-Gel, and chemical deposition.
特殊的材料包括球墨铸铁和钢煅品，大部分机轴经过热处理，表面硬化、渗氮和感应淬火。
Typical materials include ductile iron castings or steel forgings. Most crankshafts require some form of heat treating including case hardening, nitriding and induction harden.
使用两种钢基材进行比较：一种未经任何表面处理，另外一种经过磷酸化表面处理。
Two surface treatment methods for same steel substrate are used and tested: one surface without any treatment and the other with a phosphatizing surface treatment.
特点：外围罩壳为全封闭形式，材料采用不锈钢，内部台面用不锈钢材料，转台表面经过特殊处理，能保持表面光泽与防止交叉感染，符合GMP要求。
The surface of the rotary table receives special treatment so that it mainly applies to the tablet surface gloss and prevent cross infection, and conform to GMP requirements as well.
利用强流脉冲离子束（HIPIB）对316L不锈钢进行了表面辐照处理。
The surface of 316L stainless steel was treated by high-intensity pulsed ion beams(HIPIB).
应用新型的稀土处理钢用保护渣没有发生拉漏事故，并提高了铸坯表面质量。
Break out accidents have never occurred and surface quality of slabs has been improved since introduction of this new type of mould flux into continuously casting the rare earth treated steel.
磨削强化处理技术是利用磨削热替代高、中频感应淬火热源对钢件表层进行强化处理，将磨削加工与表面强化合为一体。
Grinding hardening, the technology of hardening steel piece surface with grinding heat instead of high or medium frequency induction hardening heat, can integrate grinding surface hardening.
热处理、碳化、淬火硬化层，表面覆层，钢，有色金属，微小及薄形零件等。
Heat treated layer, carbonized layer, hardened hard layers, superficial coating, steels, non-ferrous metal, micro and thin shaped components.
不锈钢加工一般分为剪切和表面处理。
Stainless steel processing is generally divided into shear and surface treatment.
试验结果表明：辅以超声波作用的电化学技术可以在常温下快速去除不锈钢表面的高温热处理致密氧化皮，恢复了不锈钢的金属色泽表面。
The results show that the electrochemical technology coupled with ultrasonic actions can remove oxide films rapidly at room temperature and renew the metallic luster of stainless steel.
本文对比分析了氮基保护气氛和真空两种热处理加热介质对300M钢疲劳性能的影响，并研究了热处理后表面喷丸强化对300 M钢疲劳性能的改善情况。
In this paper, the effect of heat treatment by the nitrogen atmosphere and vacuum furnace and shot peening thereafter on fatigue properties of 300m steel were studied.
研究了Q 235钢在经表面渗氮化钛处理后，其在10%的硫酸与富液中的耐蚀性能。
The corrosion resistance of Q235 steel in 10% sulfuric acid and rich liquid was studied after steel was treated through the surface nitridation titanium.
本文研究了用机械抛光、化学抛光和氢还原法处理轴承钢表面对测定氧的影响。
In this paper mechanical polishing; Chemical polishing and hydrogen reduction methods used im cleaning bearing steel surface for oxygen determination have been studied.
应用推荐