它的小信封使太小接受的标准编码器的理想选择位置和速度控制的机制文书轴。
Its small envelope makes it ideal for instrument axes for position and speed control in mechanisms too small to accept standard encoders.
目前常用的伺服电机是交流伺服电机，在电机的轴端装有光电编码器，通过检测转子角度用以变频控制。
Now commonly used servo motor is ac servo motor, the axial end in motor with photoelectric encoder, by examining the rotor Angle to frequency conversion control.
视频编码器作为一个实体，通过不同的控制块映射不同的编码通道，通过消息传递机制与其他实体进行通信协作。
As an independent entity, video coder USES different control blocks for different coding channels, and communicates with other entities through a 'message delivery' mechanism.
多极磁铁转子广泛使用在各种速度和整流应用中，如对旋转编码器，里程表和机器的控制。
Bonded multi-pole magnet rotors are used in a wide variety of speed and commutation applications such as to rotary encoders, speedometers and machine controls.
除了控制的机械轴和轴承载荷，耦合进一步保护通过提供电力和热轴之间的耦合隔离高度编码器。
In addition to controlling mechanical shaft and bearing loads, the coupling further protects the encoder by providing a high degree of electrical and thermal isolation between coupled shafts.
本文还讨论了场景切换对编码器质量的影响，以及相应的控制策略。
In this dissertation, the influence of scene cut on encoder and the relational control policies are discussed.
采用微处理器、专用的运动控制和驱动芯片以及光电编码器实现了机器人关节的伺服闭环运动控制；
Microprocessor, dedicated motion controller and driver, optical electronic encoder were used to realize servo closed-loop motion control.
常用的伺服电机是交流伺服电机，在电机的轴端装有光电编码器，通过检测转子角度用以变频控制。
Commonly used servo motor is ac servo motor, the motor shaft with in the photoelectric encoder, by detecting the rotor Angle to frequency conversion control.
对于光电编码器信号的采集计数和控制，通常采用专用的计数模板来实现。
The special counter modules are used to realize acquisition counter and control the signal of photoelectricity encoder.
准确的定位和控制由伺服电机编码器。
The positioning and accuracy are controlled by encoders from servo motors.
准确的定位和编码器是由伺服控制马达以及高精确度的三件希斯耦合。
The positioning and accuracy are controlled by encoders from servo motors as well as a high precision three-pieces Hirth coupling.
介绍了增量式和绝对式编码器在同步丝杆控制中的应用和软件编制。
This paper introduces applications of the incremental and absolute angular encoders in synchronous leading screw control.
叙述了旋转编码器在有轨缆车plc控制系统中的应用。
Circumvolve coder application in the rail cable car PLC control system was discussed in this paper.
T2编码器由已编码比特率自适应地反馈控制编码深度，完成优化截取。
T2 encoder sends feedback to control the coding depth by the accumulated bit rate and complete the rate-distortion optimization truncation.
用凌阳SPMC75F2413A单片机配合编码器对直流电机进行闭环反馈控制，使直流电机带动的钩状扫描针停在规定的位置上。
Closed feedback control to DC motor was made by PID based on SPMC75F2413A SMC and coder in order to make the hook-liked scanning probe driven by the DC motor to rest on the specified position.
在传统的运动控制系统中，通常采用光电编码器或旋转变压器来检测转子的位置和速度。
In conventional motion control systems, photoelectric encoders or rotary transformers are used for this purpose.
头架主轴(c1轴)采用高精度滚动轴承主轴结构，配置角度编码器闭环反馈控制，达到极高的回转精度和定位精度。
Work head spindle (C1axis) USES high precision rolling bearing structure, and Angle encoder close-loop control, which make it get extremely high rotary precision and positioning precision.
在传统的运动控制系统中，通常采用光电编码器或旋转变压器来检测转子的位置和速度。
In conventional motion control systems, optical encoders or electromagnetic resolvers are used for this purpose.
设计了基于CAN总线的地址编码器，通信总站的数码显示电路，控制继电器电路，LNK501开关电源芯片电路。
Design the CAN bus address encoder, communication terminal digital display circuit, control relay circuit, LNK501 switching power supply chip circuitry.
设计的编码器，全部控制电路由一片可编程逻辑器件(PLD)来完成，减小了电路板的面积。
In the designed encoder, all of the control circuits are realized with a PLD (Programmable Logic Device). The area of the printed circuit board is reduced obviously.
它采用了微处理器、专用的运动控制和驱动芯片以及光电编码器，实现了机器人关节的伺服闭环运动控制。
The microprocessor, dedicated motion controlling and driving chip, optical encoder are adopted to realize the joints 'closed-loop servo motion control.
加之每块计数模板控制通道数量的限制，在光电编码器应用数量较多的系统中，会增加计数模板的数量并占用大量的系统资源，增加控制成本。
The number of each counter modules channel is limited, it needs a lot of counter modules and system resource in the system of photoelectricity encoder is much , and it can increase control cost.
采用光电编码器、高速计数模板、PLC程序控制方案实现钢板的定位剪切，提高了中板成材率。
By using encoder, high speed counter module and PLC sequencing control in steel plate positioning shearing, medium plate yield have been increased.
应用光电编码器作为滚珠丝杠转角位置检测元件实现了半闭环补偿控制，提高了系统的精度。
The photoelectric encoder is used for measuring the angular position of rotating ballscrew. Semi closed loop compensation control is realized and system accuracy is improved.
该运动控制卡能同时采集四轴的编码器脉冲信号，输出四路模拟电压控制伺服电机，同时能控制I/O信号的输入和输出。
The card can collect four axes' encoder pulse signals simultaneously, and control servo motor by four output analog voltage. Furthermore, it can control input and output I/O signals.
由SFCD WARE软件、SS2000D编码器和数字化警报控制器组成的联邦指挥能够确保社区保护功能以更加简单的方式实现。
Consisting of the SFCDWARE software, SS2000D encoder and the Digital Siren Controllers, the Federal Commander makes protecting communities simpler.
探讨了PC的串行接口用于光电编码器的脉冲计数和伺服电机控制两种非通信功能的应用。
The COM of IBM-PC applications for the counter of Opt-encoder pulse and the controller of AC -Servo are study in this paper.
探讨了PC的串行接口用于光电编码器的脉冲计数和伺服电机控制两种非通信功能的应用。
The COM of IBM-PC applications for the counter of Opt-encoder pulse and the controller of AC -Servo are study in this paper.
应用推荐