提出了组态软件现场应用时通信受干扰的问题。
This paper presented the communication failure when using SCADA software in practice.
本文提出了采用组件化规范和技术设计组态软件。
Raise a point of designing configuration software with COM and associative technologies.
介绍所开发的SFC组态软件的图形系统的构成。
The graph system of the SFC configuration software is introduced.
图形组态子系统是组态软件一个重要的组成部分。
Graph configuration SubSystem is an important part in industrial configuration software.
图形组态子系统是工控组态软件的重要组成部分。
Graph configuration subsystem is an important part in industrial configuration software.
介绍基于工控组态软件MCGS的船舶轴系监测系统。
The system of shafting monitoring on the spot of configuration software MCGS is introduced.
实时数据库系统是DCS组态软件体系结构的关键部分。
Real time database is the critical component of architecture of DCS configuration software.
介绍一种基于组态软件车用水泵性能测试系统的设计方法。
The design method of a performance test system of automobile water pump based on configuration software is introduced.
组态软件友好的人机界面使得控制系统的操作更加简捷，方便。
The friendly man-machine interface of the configuration software makes the operation of the control system more swiftly and conveniently.
结合一实际对象介绍了组态软件与仪表进行通讯的原理与方法。
The principle and method of the communication between the configuration software and the instrument with a practical object was introduced.
IPC系统使用组态软件来实现系统的监视、保护等管理功能。
IPC system is adopted with configuration software to realize monitoring and management functions.
组态软件甚至可用于智能大厦管理、会议室声光控制、温度调整等。
It can also be used in intelligent building management, office acoustooptic control, and temperature adjust, etc.
介绍了通过DDE通讯在组态软件环境下对CAN适配卡的驱动编程。
Programming of driver for CAN adaptor in configuration soft by DDE communication was introduced.
在组态软件MCGS的基础上，作者研究提出了虚拟PLC系统的方案。
The plan of virtual PLC system is brought forward based on configuration software MCGS.
目前基于工业组态软件的远程PLC虚拟控制系统在教学上尚无具体的应用。
At present, remote PLC Virtual control system based on industry configuration software still has not concrete application in teaching.
实践证明该方法弥补了现有组态软件的不足，设计灵活，系统运行稳定、可靠。
Practice shows that this method remedies the insufficient of present software, is with features of flexible design, steady and reliable running.
本文主要是介绍在WINCC组态软件中采用OLE控件实现串口通讯的方法。
This paper describes the method of realizing serial communication with OLE based on WINCC.
把柔性控制、工业网络、组态软件等结合使用，解决了高压提金新工艺中的难题。
Through combining the flexible control, industrial network and configuration software, the tough problems in new high pressure gold leaching technique are resolved.
通过实例说明了组态软件与VB应用程序之间利用DDE进行数据通信实现方法。
And it is illustrated that data communication can be carried out between configuration software and VB application by using DDE.
本文以主要的篇幅来介绍人机界面组态软件和控制器之间通讯的设计和开发过程。
What is mostly discussed in this paper is how the control system communicated with HMI configuration software.
到目前，市场上的计算机监控软件主要有两种：组态软件和专用的计算机监控软件。
Now, there are two kinds of computer monitoring and controlling software in the market: configuration software and appropriative computer monitoring and controlling software.
介绍了在面向温室农业生产监控过程的工控组态软件建设中，实时数据库系统的设计。
In the construction of industrial control configurable software for greenhouse agriculture production detection and control process, design of real-time database system is introduced.
本文采用工控组态软件MCGS作为开发环境，介绍了包含三个部分的测控系统的开发。
This thesis use the Monitor and Controll Generated System(MCGS) as the the software developing environment.
介绍了一种采用工业控制组态软件，以模块化方式组建内燃机台架综合测控系统的方法。
An engine rig test system with a control system based on industrial control configuration software module has been introduced.
该组态软件分为PC机软件和单片机软件两个部分，这两个部分都采用模块化设计思想。
The configuration software is divided into PC software and Single Chip Micyoco software. The modularization design idea is adopted in this paper.
其连接方法和通用的RS- 485输出接口一致，注意您应该提前申购远传组态软件。
The connection method and the common RS-485 output interface consistent, note that you should purchase in advance remote configuration software.
在分析组态软件体系结构的基础上，详细分析及研究了操作员站各个模块的功能及实现方法。
After analyzing the configuration software architecture, we analyze and study the function of each module and method of implementation of the operator station.
本文介绍一种应用MCGS组态软件的纺丝机断丝检测管理系统，描述了系统的设计和实现。
This article introduces an application of MCGS configuration for yarn break inspect and manage system, describes the designing and achieving of the system.
介绍了一种DCS开放式组态软件，并详细叙述了面向对象程序设计方法和控制回路识别技术。
The paper introduces an open configuration software of distributed control systems (DCS), especially describes the object oriented programming design and the techniques of control loop identification.
本文的目标是开发一个图形化控制策略组态软件，以生成控制器所需要的完成控制功能的软件。
This paper aims at exploiting a graphic control strategy configuration software, in order to create required control strategy of controller.
应用推荐