实现此目标的最佳方法是，找到给定站点与稳定的可理解的站点之间的最短路径。
The best way to do that is to find the shortest path between the site you are given and one that is stable and understandable.
通过计算短路点的短路电流，说明原电流互感器额定热稳定电流太小。
The short circuit current calculation shows the rated thermal stability current of former current mutual inductor is too small.
气中电火花加工时电极相对损耗很小，但由于短路率过高导致加工不稳定、材料去除率不高，还会产生烧焦气味。
EDM in gas can make less electrode wear, but its high short circuit ratio will lead to unstable process and thus low material removal rate.
同时为了选择与最短路径相似的稳定多路由，RNDMRA应用相似性因子选择相似的稳定节点不相交多路径路由。
And in order to select stable multiple routes similar with the shortest path, RNDMRA USES similarity factor to select similar stable node-disjoint multipath routes.
简述了短路电弧焊接的物理过程及过程稳定性概念，介绍了有关短路焊接过程稳定性各种评价方法及相应准则，最后对其进行了必要的讨论。
This paper interprets the short-circuit arc welding process and the process stability. The evaluation methods and criteria for the short-circuit arc welding process are introduced and discussed.
验证短路故障条件下，直流侧的负载转换器的动态稳定的特点。
Verify that the DC side load converter dynamic stability characteristics under short-circuit fault conditions.
为了分析短路过渡电弧的焊接过程和探讨电弧能量对焊接稳定性的影响，设计了短路过渡电弧电参数检测系统。
A arc parameter-measuring system was developed to analyze the process of short-circuiting arc welding and the effect of arc energy on the welding stability.
选用站用电系统设备时应满足短路时的动、热稳定，开断电流，开关上、下级的选择性等要求。
It should satisfy dynamic stability, thermal stability, switched-current and switch up-down selectivity in a short circuit while selecting the pumping station using electricity system equipments.
大负荷中心短路电流超标严重影响电网的安全稳定。
The short circuit current of large load center that excesses the regulation standard seriously endangers security and stability of power grid.
短路过渡焊接时，熔滴过渡频率通常被作为评价焊接过程稳定性及焊接质量的重要指标。
Metal transfer frequency are usually taken as the criteria to evaluate the process stability of short-circuiting arc welding.
本文主要论述了电力系统中母线上发生三相对称短路时，其动稳定和热稳定的校验问题。
This paper discusses the short-circuit verifying of wires in dynamic stability and heat withstand while the wires are chosen in the design of power system.
仿真结果表明：当南桥、华新换流站发生直流输电单双极闭锁以及交、直流侧短路故障时，不会给系统带来稳定问题。
The results show that occurrence of the single or double pole block on the DC lines, or short-circuit faults on the DC or AC lines will not influence seriously on power system stability.
并证明，该方法构造的神经网络只有一个稳定点，且从任意初始点均可收敛到该稳定点，该稳定点恰好对应图的所有最短路径。
The network can converge to this equivalence-point from arbitrary initial point and this equivalence-point corresponds exactly all the shortest path pairs of the graph.
从绝缘导体短路热稳定的基本概念出发，分析热稳定校验公式的由来与内涵，探讨满足绝缘导体短路热稳定要求的多种办法。
The paper analyzes origin and connotation of thermal stability calibration formula from basic concept of insulating conductor thermal stability, and discusses some means for thermal stability.
试验结果表明，通过对短路过渡过程中各个不同阶段的输入能量的控制，可提高焊接过程的稳定性，实现CO2焊的高速化。
The results show that the welding stability can be improved by controlling the input energy in each period to achieve high-speed CO2 arc welding.
为了使系统更稳定可靠，提升了系统的防雷能力和防静电能力，并为传感器电源设计了传感器电源短路保护电路。
In order to strengthen the stability and reliability of the system, lightningproof and static-free protection is improved and power trip protection circuits are added to to the design of senor power.
仿真结果表明所建立的负荷模型在单相短路、两相短路和三相短路条件下均具有良好的稳定性和准确性。
The simulation results suggest that the proposed load model be quite stable and accurate under the single-phase short faulty, two-phase short faulty and three-phase short faulty.
基于有限元计算结果，将边坡稳定性问题转化为图论中寻找最短路问题。
Based on the calculated results of finite element method, the problem of slope stability could be converted into searching for the shortest path in graph theory.
该器件具备完整的安全特性，包括短路保护、过压保护和过温保护，因而很容易实现安全、稳定的设计。
A full suite of safety features including short-circuit, overvoltage, and over-temperature protection allows easy implementation of a safe and robust design.
电力系统的容量和短路电流越来越大，相应的对系统的稳定性和断路器的开断能力等提出了更高的要求。
As the power systems expand, the fault currents would be increase to exceed the instantaneous capacity and the interrupting capabilities of the existing circuit breakers.
电力系统的容量和短路电流越来越大，相应的对系统的稳定性和断路器的开断能力等提出了更高的要求。
As the power systems expand, the fault currents would be increase to exceed the instantaneous capacity and the interrupting capabilities of the existing circuit breakers.
应用推荐