给出了修正方法及微机计算程序框图。
The amendment method and the block diagram of calculation program for the microcomputer are given.
最后，给出了虚电路中实现这些进程的程序框图。
Finally, it gives the program flow diagram of these processes in virtual circuits.
介绍了三个变量的寻优方法并给出了寻优的程序框图。
The optimization of the three variables and its program block-diagram are also presented.
详细描述了硬件电路的设计，并给出了软件程序框图。
The design of hardware circuit is explicated and the diagram of program is offered.
对于主程序的描述，还给出了大量的流程图和程序框图。
In the description of main program, the paper gives lots of flow charts and procedure block diagrams.
这样的图表叫做程序框图，动作的过程在图中很容易看出。
Such a diagram is called a flow chart and the path of action is easily seen in the chart.
除了对硬件的介绍还针对软件设计思想及程序框图做了介绍。
In addition to hardware presentation also against the software design process diagram and made a presentation.
文章介绍了血流速度测量原理并给出了硬件结构图和程序框图。
In this article is also introduced the principle blood flow velocity measurement. Hardware configuration and software block diagram are given.
在工具选板上选取断点工具，单击程序框图上的对象，就放置了断点。
To set a breakpoint, click on a block diagram object with the breakpoint tool from the Tools palette.
本文提出了隧道窑窑车的二维非稳态传热数学模型及计算机程序框图。
Mathematical model and computer programme flow diagram for two-dimensional transient heat transfer in tunnel kilns are presented.
如图5.8所示一个程序框图上有两个探针分别放置在两条数据线上。
Figure 5.8 shows a VI block diagram with probes placed on two of the wires.
本文讨论了复杂巨系统中的智能经济控制问题，并给出相应的程序框图。
This paper discussed the problem of intelligent economic control of complex system, and we represent the process frame.
介绍了系统工作原理、串行通信方法，给出了硬件电路结构及程序框图。
The operational principle of the system and serial communication method are presented. The hardware structure and program block diagram are given.
本文简要地介绍了方差分析的原理，给出了计算机程序框图和详细的程序。
The principle of variance analysis was introduced briefly. The block diagram and program of computation were given.
文中介绍了系统的特点，列举了串联谐振中各频率特性的计算公式及程序框图。
The Character of the system, the calculative formula of the frequences as well as flow chart of program have been presented in this paper.
本文给出了两种算法的计算机程序框图，并就结果与直接求导方法进行了对比。
In the paper, algorithm block diagrams are given, and results are compared with that by direct derivation method.
在说明了该传感器所具有的特点之后，给出了该传感器软件设计方法和主程序框图。
After narrating the characteristic of the intelligent temperature sensor, the design method of software and main program frame were given.
当一个VI由于断点暂停时，程序框图会会弹出，并且导致暂停的对象会高亮显示。
When a VI pauses because of a breakpoint, the block diagram comes to the front, and the object causing the break is highlighted with a marquee.
本文对系统的测量原理、性能指标及硬件组成作了简要介绍，并给出了主要程序框图。
The principle of system measurement, performance index and hardware construction are described simply, and the block diagram of main program is given.
在分析原脉冲反吹控制系统的基础上提出了一改进方法，给出了具体程序框图和程序。
On the basis of analysis of the former pulse inverse blow control system, improving methods are proposed and actual program block diagrams and programs are given.
文中详细介绍了该系统的工作原理，并且给出了它的硬件原理图和软件设计程序框图。
The work principle is presented in detail in this paper and the block diagram of as well .
本文主要介绍太钢新横切机组PLC控制系统的硬件配置、控制功能及软件程序框图。
This paper mainly introduces the PLC (Programmable Logic Controller) control system of new-style cross cutting unit. The function of this system.
推导了模拟多层样品显微成像的数学模型，给出了用程序框图表示的基本仿真系统骨架。
The mathematical model used to microscopically image multi layered tissues is presented. The basic skeleton of the simulation program is demonstrated with flow chart.
设计了系统中的各主要部件，绘出了程序框图，指出了程序设计方法，考虑了抗干扰措施。
Mian components in the system are designed, block diagram of program drawn, method of program composition provided and particularly anti-interference measures taken into consideration.
本文着重阐述采用微处理器控制SCR交流调压的工作原理，系统的硬件组成及程序框图。
This paper puts emphasis on the principle of using microprocessor to control SCR for the adjustment of alternating voltage, and on the hardware system and the flowchart.
设计了两种新型凸轮滑杆式间隙模封机构，同时采用微机控制，给出硬件、软件程序框图。
Two new intermittent traverse seal mechanisms were designed. They were controlled by the computer. The hardware and software program drawing were also presented.
文中给出了系统硬件构成以及软件的程序框图，讨论了单片机控制产生添加信号的设计原理。
The hardware configuration and the software flowchart of the system are given, and the design principle for adding signals by the monolithic microcomputer discussed.
本文利用灰色系统理论建立了学期考试平均成绩的预测模型，并给出计算机处理的程序框图。
This article establishes the prediction model of the average marks of a term's examinations by applying the theory of grey systems, and presents the flowchart of computer treatment.
文中系统地介绍了轴承产品计算机设计的全过程，并给出了CAD系统工作流程图和程序框图。
In the paper, the whole process of bearing product CAD is systematically introduced, and the working flowchart and program chart of CAD system are given.
本文介绍了具有通信功能的数据采集系统，并重点介绍了通信程序设计，给出了部分程序框图。
The data acquisition system with communication function and the communication program design are introduced with parts of the flow charts given.
应用推荐