该算法与电路的输入变量数无关。
This algorithm is independent of the number of input variable in the circuit.
当滑动头移动时，就改变了电路的输入电压。
When sliding the first move, to change the circuit's input voltage.
带电物体接近被测电路的输入端时，就会发生静电耦合和干扰。
Electrostatic coupling or interference occurs when an electrically charged object approaches the input circuit under test.
如果想减小输出噪声，可以在上述电路的输入端采取旁路措施。
Output noise may be reduced in both circuits by bypassing the amplifier input.
运用理想电源转移规则，可以把这些误差源转移到放大器等值电路的输入支路。
According to the rules of ideal source transformation, we are able to transfer the equivalent error sources to the input branch of the amplifier's equivalent circuit.
在通信技术中，通过公共载体将电路的输出部分返回到电路的输入部分的一种连接。
In communications, the connection, by a common carrier, of the output portion of a circuit back to the input portion of a circuit.
提出电路的输入电感工作在不连续导电模式（DCM），而输出电感工作在连续导电模式（CCM）。
The input inductor can work at its Discontinuous Conduction Mode (DCM), while the output inductor works at its Continuous Conduction Mode (CCM).
如果被验证的电路是从设计中勾画出的，那么电路的输入波形必须被配置为与当电路被嵌入到设计中时的一样。
If the circuit under verification is carved out from the design, the input waveforms to the circuit must be configured to be identical to them when the circuit is embedded in the design.
L 297芯片产生脉宽可调的脉冲相序信号，该信号作为双极性桥式功率驱动电路的输入信号，放大后驱动步进电机。
L297 chip generates pulse phase sequence signals of which the pulse width is adjustable. The signals are the input ones of dual bridge driving circuit and drive the stepper motor after amplification.
在短时间内，有望看到这种逻辑电路制作的输入输出设备，如显示器和电力设备，它们都可以制作成柔性的形式。
It is, in short, possible to see how logic circuits, input sensors, output displays and power supplies can all be made in flexible form.
假设，一个最简单的电路，只有一个数字输出端连接一个数字输入端。
Consider a simple circuit that consists of one digital input connected to a digital output.
毫无疑问，两个电路在该输入序列下是不等价的。
Surely these two circuits are not equivalent under this input sequence.
数字式电压表通常有10兆欧的输入阻抗。当测量高阻抗电路时﹐可能会有影响。
DVM usually got an input impedance of 10 Mohm. There may be loading effect when measuring high impedance circuit.
Sinking和Sourcing指的是数字电路中使用的输入和输出的类型。
Sinking and sourcing refer to the type of digital inputs and outputs used.
给出了系统设计方案，其存储器技术的应用以及CRT驱动电路与光笔输入系统设计思想。
The design scheme for display operating, the application of memory technology, the design ideas for CRT drive circuit and light pen input system have been given.
在这种情况下，就需要附加的过载保护功能以避免损坏仪器的输入电路。
In these cases, additional overload protection is required to avoid damaging the input circuitry of the instrument.
只有一个输入的数字电路单元是缓冲器或反相器，而输入在一个以上的则称为逻辑门。
Only one input of the digital circuit unit is the buffer or inverter, the input in more than one are called logic gates.
仪器内部电路和内部的偏移电压会在仪器的输入端引起输入偏置电流。
The input bias current flows at the instrument input due to internal instrument circuitry and the internal bias voltage.
如果等价性检查失败，检查器会生成一个输入向量序列，它可以在仿真中使用以便演示两个电路之间的差异。
If an equivalence check fails, the checker generates an input sequence of vectors that, when simulated, demonstrates the differences between the two circuits.
设备设计师能通过审慎地选择输入输出级电路的拓扑和共模阻抗来最小化失配或“非平衡”的效应。
Equipment designers can minimize the effects of these mismatches or "unbalances" through judicious choices of input and output stage circuit topologies and common-mode impedances.
输入电源的过电冲击常常会形成驱动电路中驱动芯片的损坏，以及电容等被动元件发作击穿损坏。
Input power over the impact of power will often form a drive circuit driver chip damage, as well as passive components such as passive breakdown breakdown.
设计出传感器输入输出信号调理电路和试验台架液压激振系统、磁流变阻尼器控制器的功率放大电路。
Design the signal adjust circuit for sensor, and the power amplification circuit for the hydraulic pressure system of test platform and the controller of magnetorheological dampers.
输入电路和功率放大电路的原理图设计。
这些误差源包括热电动势、由射频干扰(RFI)经过整流而产生的偏置量以及电压表输入电路中的偏置量。
These sources include thermoelectric EMFs, offsets generated by rectification of RFI (radio frequency interference), and offsets in the voltmeter input circuit.
在系统中专门设计了输入输出点处理电路，它可以实现32个输入点信号的输入和实现32个输出点的控制。
Processing circuits of input and output are designed specially, which can realize the input of 32 inputting signal and control of 32 outputs.
虽然输入偏置电流是这种误差的常见来源，但是外电路产生的电流在源电阻上形成的电压降也能引起误差。
Although input bias current is a common source of this type of error, currents generated by external circuits can also result in errors due to voltage drops across the source resistance.
虽然输入偏置电流是这种误差的常见来源，但是外电路产生的电流在源电阻上形成的电压降也能引起误差。
Although input bias current is a common source of this type of error, currents generated by external circuits can also result in errors due to voltage drops across the source resistance.
应用推荐