电机电流控制器可以装载高达1A，取决于电感。
The Motor current controller can be loaded with up to 1a, depending on the inductors.
并通过变参数PI数字电流控制器构成电流闭环系统。
The current closed-loop system is composed of current controllers that control variable parameter PI.
其控制系统由两个PI电压控制器和一个滞环电流控制器组成。
The control scheme consists of two PI voltage controllers and one hysteresis current controller.
文章提出了一种基于滞环控制和预测控制的自适应电流控制器。
This paper presents a new self-adaptive current controller based on hysteresis control and predictive control.
该系统使用了一种新的电流控制器，以改善电机转子电流波形。
A novel current regulator was used in the control system to improve the rotor current waveform.
控制系统包括两个采用ADRC的电流控制器和一个基于“微分检测”的电压控制器。
The control system consists of two current controllers using ADRC and one voltage controller based on differential coefficient detection.
采用短路电流控制器和动态电子电抗器，实现了脉冲MIG焊动态特性的自适应控制。
The self-adaptation control of dynamic characteristics of pulsed MIG welding was achieved by a short circuit controller and a dynamic electronic inductor.
内环电流控制器采用电流反馈和电压前馈的解耦控制策略，实现电流的快速跟踪控制；
Decoupled control structure consisting of current feedback and voltage feed-forward is adopted in the inner current control loop which can track the reference current quickly.
提出了一种采用直流脉冲电流的埋弧焊工艺，研制开发了以单片机为核心的脉冲电流控制器。
It will introduce us a new SAW process by adopting DC pulse current. They design and develop pulse current controller as core of single plate machine.
高精度大电流控制器有着广泛的应用，但在高共模电压情况下输出电流的检测电路比较复杂。
The high precision and large current controller are used widely. But in the situation where there is high common-mode voltage, the detection circuit of the output current is very complex.
将模糊控制技术引入到了感应电动机矢量控制+位置伺服系统中，设计了模糊位置和电流控制器。
Fuzzy control strategy is introduced into a field-oriented controlled induction motor servo system in this paper.
并利用电流控制器来控制电流量的大小与电流的方向性，以达到增减电磁力的强度与磁极的方向。
In addition, the current controlling device is used to control the amount and the direction of the current, and thus control the strength of the electromagnetic force and the polarity.
介绍了带有转子电流控制器(RCC)的变桨距调节异步风力发电机系统的基本原理及其控制策略。
Fundamental principles and control strategies of pitch-controlled wind induction generator system with rotor current controller (RCC) were presented.
本文通过对传统滞环电流控制器的分析，结合电压空间矢量调制方式，提出一种改进的滞环电流控制方法。
This paper presents a sort of improved hysteresis current control method through analyzing the traditional hysteresis current controller and combining voltage space vector modulate method.
对并联型电力有源滤波器建立了数学模型，详细地分析了在全数字控制下，谐波指令的生成和电流控制器的设计。
Having established the mathematic model of a parallel active power filter, this paper has analyzed the generation of harmonic current order and the design of its current controller in detail.
该系统的思路是通过DSP输出PWM波形控制电流控制器的输出电流，从而实现调节磁流变阻尼器阻尼力的大小。
The main idea of the control system is that PWM waves from DSP adjust outputting current from the current controller which can change the MR damper damp power.
触发电路板由两部分组成，第一（上半部分示意图）的触发和恒定电流LED驱动器和第二届（下半部分）的PWM电动机电流控制器。
The trigger PCB consists of two parts, first (upper half of the schematic) the trigger and constant-current LED drive and second (lower half) the PWM motor current controller.
当这些线圈被调节到合适的操作频率，电流就可以通过一个开关控制器转换给这些线圈。
The coils all get tuned to the right operating frequency and electricity is transferred to them using a switch-mode controller.
需要符合CCC标志的安全产品包括继电器、开关、控制器和高于36伏特的电流接触器。
Safety products subject to the CCC mark include relays, switches, controllers and contactors that operate above 36 volts.
利用非速度信息，如：电机的电压、电流及电机本身参数，通过滑模观测器产生控制器所需的速度反馈信息。
The control system utilizes a sliding mode observer for the generation of all controller feedback information by means of non-speed information, such as voltage, current and parameters of motor.
控制器通过监测电机定子电流的大小，将其起动电流控制在允许的范围内。
Through the detection of the stator current, the control can confine the starting current within the allowable range.
详细介绍了采用单神经元自适应PS D控制器对电流环进行调节的方法，使电机能稳定工作在变负载条件下。
Controlling method of current loop with single neuron adaptive PSD controller which can make motor work stably in the condition of changing load is discussed in detail.
提出了一种新型的双重单端正激式弧焊逆变电源，采用IGBT为开关器件，引入了电流型脉宽调制控制器。
A new double single-ended forward arc welding power inverter with IGBT as power device and current PWM controller is introduced in this paper.
本文提出了一种基于DSP的直流无刷电机控制器的硬件电路，包括电流环、速度位置环和IPM(智能功率模块)驱动的硬件电路设计。
In the paper, the hardware circuit design of a DSP-based Brushless DC Motor Controller is given, which includes a current loop, a speed position loop, and IPM (Intelligent Power model) driver.
控制器由AT89C52单片机，AD转换电路，LCD显示电路，电流电压采集电路以及控制电路等组成。
This design's hardware consists of minimum system circuit in MCU AT89C52, AD convert circuit, LCD display circuit, the monitor and control circuit of current voltages.
本文介绍了用8031单片机研制的定电流，多脉冲电阻焊机控制器的硬件电路及软件程序的特点。
The hardware circuit and software program features of the given current, multi-pulsed resistance welding machine controller developed 8031 single chip processor are introduced in this paper.
同时配备缝焊控制器，对焊接时间，间歇时间，焊接电流能精确的设定和控制。
Equipped with welding controller, the welder has precise control and setting functions for the welding time and intervals and welding current energy.
介绍基于MC33035高压无刷直流电动机控制器尖峰电流的几种抑制方法。
This paper introduces the suppression methods of spike current in the high voltage brushless DC motor controller based on MC33035.
结合设计出的电流泵控制器共同组成蚁群并联光伏发电系统。
Combined design of the current Pump Controller together constitute the ant parallel photovoltaic power generation system.
结合设计出的电流泵控制器共同组成蚁群并联光伏发电系统。
Combined design of the current Pump Controller together constitute the ant parallel photovoltaic power generation system.
应用推荐