然而在磁回路的电机片和电枢之间有一个间隙，于是产生一个力，其作用是关闭这个间隙以完成这个磁回路。
There is however a gap in the magnetic circuit between the pole piece and armature so a force is created which ACTS to close this gap and complete the magnetic circuit.
间距控制：为了最大限度地根据风速变化提升发电效率，新型风力发电机上的控制器每秒钟都能够对每一片风叶进行任何角度的调整。
Pitch controller: to maximize lift as the wind speed changes, a controller can automatically rotate each blade anywhere from a fraction of a degree to multiple degrees per second.
人们对戈德博格的著名卡通片和19世纪20年代的波浪发电机都很好奇。
There's a curious resonance between Goldberg's famous cartoons and the wave motors of the 1890s.
介绍了大型电机定子扇形片模具结构的设计，及零部件设计加工难点和解决办法。
Die structural design of large-scale motor stator sector piece, difficulties and solving steps in design and manufacture of parts and components are introduced respectively.
文中导出了计算直流电机换向器片间电压分布曲线的基本公式和试验验证；
Basic formulas for the calculation of bar to bar voltage distributing curve of DC motor commutator are derived and test-verified.
介绍了为实现削片机传动的运行所进行的提提要：高压电机的电气设计、控制逻辑以及实现这一控制逻辑所采取的控制方式。
This paper introduces the electrical design for the high voltage motor to realize the running of the chipper, the relevant control logic and the control mode for realizing the control logic.
提出了一种圆筒型错片结构微型直线步进电机。
The paper puts forward a cylindrical staggered-sheet structure micro linear stepping motor.
分析了电机冲片单冲模原结构存在的问题，并采取了相应对策通过两次改进，取得了良好的效果。
The existing problems of the previous structure of the single stamping die for motor blanks. And the corresponding measures were adopted. After two_time improvement, good results were received.
并且通过步进电机，抽水机，电热片，植物生长灯等执行器对参数进行控制，达到智能调控的目的。
And through the stepper motor, pumps, electric films, such as plant growth lights for the implementation of the parameters of control, intelligent control to achieve the objective.
设计出了一种机电一体化的特种电机——永磁扇片定子电动机。
This paper presents a type of special electrical machine with the electromechanical integration_per-manent magnet sector-stator motor.
通过设置TMC428内部参数寄存器和片内ram的值，可使TMC428能够同时控制三个步进电机，实现三轴控制系统。
To set the proper parameter of register and on-chip ram of TMC428, it can make TMC428 control three stepper motor in the same time, and realize three-axis control system.
用途：适用微电机冲片入轴或类似机械压入装配。
Usage: suitable for micro motor punching sheet pressing to shaft or similar mechanical pressing and assembling.
基于DSP的全数字化无刷直流电机伺服系统，由包括DSP和片外存储器的以TMS320F240组成的小系统，及反馈信号采集模块2部分组成。
The servo system for full-digital BLDC motor consists of DSP, memory subsystem based on TMS320F240 and the module for feedback signal acquisition.
螺旋爆气机由驱动电机，空气轴，螺旋浆片，外壳组成，所有材料都耐腐蚀，浸沉部分由不锈钢或纤维增强材料制成。
Spiral Aerator is consisted of driving motor, air shaft, spiral impeller, out-shell; all the materials are erosion resistance and the dipped parts use stainless iron or FRP.
介绍了无涂层电工钢冲片叠片成型后的电机定子和转子在罩式炉内进行退火和发蓝处理一次完成的新工艺及装置。
A new technology and equipment of annealing and bluing for finished stator and rotor of uncoated cold-rolled electric steel lamination in bell-type hytrogen furnace was introduced.
在实验方面，选用一个成品窄带滤光片，设计步进电机控制电路，实现了一个线性调谐光滤波器装置。
Experimentally, a linear tuning filter's set including a finished product narrowband thin-film interference filter and control circuit of stepping motor has been designed.
介绍了无涂层电工钢冲片迭片成型后的电机定子和转子在罩式炉内进行退火和发蓝处理一次完成的新工艺及装置。
A new technology and equipment of annealing and bluing for finished stator and rotor of uncoated cold-rolled electric steel lamination in bell-type hydrogen furnace was introduced.
通过对粗轧同步电机的生产，对整个加工工艺做了总结，重点介绍了斜槽冲片的加工及叠片的要求。
This paper summarizes the manufacturing technique of synchronous machine by production process of it and focuses the manufacturing and laminating requirements of the skewed slot lamination.
能量转换片是由压电陶瓷材料制成的（而不是任何机械振动或电机）。
The transducer is made of piezoelectric ceramic material, it is different from physical vibration and motor vibration.
本文针对DW620型系列电机定子片转子片的结构特点，采用体分解的方法进行冲压特征自动识别；
Body disassembled method has been adopted to perform blanking feature recognition by analyzing the structural feature of DW620 stator and rotor plate.
盘式制动器包括制动摩擦片、制动盘、制动衔铁、制动弹簧、磁轭组装、安装在电机外端内部。
The disk type brake comprises a brake strip, a brake disk, a brake armature, a brake spring and a magnetic yoke assembly which are all installed on the inner part of the outer end of the motor.
减少废料：充分利用卷料的宽度， 采用高精密伺服电机驱动系统控制， 使圆片间距和圆片到料边的距离减少到最小， 从而减小废料量。
SCRAP REDUCTION :To use the whole width of the coil, reducing to the minimum the distances between disc to disc to the strip edges, with a consequment, reduction of the scrap quantity.
通过实例分析了发电机磁轭片的冲压工艺，确立了模具结构(整极式)，并对定位装置作了改。
This article analyzes the punching procedure for generator rim laminations, establishes the die structure (for solid pole) and also improve the design of fixtures by giving some example.
用步进电机控制选择8种波长的滤光片；
文章根据硅钢片的可延展性，提出一种窄轭冲片套裁成形成冲片条，再盘卷成电机铁心的工艺方法。
According to the tractility of Silicon steel sheet, a new processing technics of cutting the narrow-yoke sheet into punching piece and rolling it into motor core was proposed here.
自动铝带绕片机数控机床是一种集成了计算机数控技术、电机驱动技术、PLC控制技术等最新成就的自动化精密机床，数控系统是其核心所在。
Automatic aluminum winding machine is an automatic accurate machine, which integrates some new technologies such as CNC technology, motor driver technology and PLC control technology and so on.
设计了发电机转子冲片槽形及阻尼孔冲模。其结构融冲槽形、阻尼孔两工序为一体。降低了模具制造成本，提高了生产率，且稳定可靠。
A die for slot punch and damping hole punch is designed for generator rotor. It can reduce the cost, raise the efficiency and reliability.
介绍了大型发电机转子核心零件磁轭冲片的超吨位模具设计新方法。
This article describes a new designing method of over-tonnage Die for rim sheet, the center part of rotor of the oversize generator.
介绍了大型发电机转子核心零件磁轭冲片的超吨位模具设计新方法。
This article describes a new designing method of over-tonnage Die for rim sheet, the center part of rotor of the oversize generator.
应用推荐