为电弧焊的自动跟踪技术提供参考。
It gives a reference to automatic arc welding tracking technique.
产品主要用于电弧焊、氩弧焊等领域。
Products are mainly used for arc welding, argon arc welding and other fields.
电弧焊的焊条是由焊芯和药皮两个部分组成的。
Electrode for arc welding consists of the core and the coat.
手工电弧焊焊缝耐腐蚀性优于超窄间隙焊焊缝。
The manual welding welded joint inoxidizability surpasses the ultra narrow gap welding joint.
手工电弧焊通常是指采用药皮焊条的手工焊接法。
The manual arc welding normally refers to the manual welding using coated electrode.
镀锌板上有焊点或焊缝，但是电弧焊会烧掉锌层。
Galvanized sheet is readily spot- or seam-welded, but arc gas welding will boil off the zinc coating.
电弧焊、二氧化碳气体保护焊、氩弧焊等各种焊接。
Such as electric arc welding, carbon dioxide gas shielded arc welding, TIG etc.
建议在钢材多层焊时使用脉冲电弧焊，也适合于炉焊。
For multilayer welding on steel, pulsed arc welding is recommended-also appropriate for oven soldering.
该电源可以用于手工电弧焊、药芯焊丝焊接及CO2焊接等。
手工电弧焊的设备包括焊接电源、电流调节器、焊钳及电缆线。
Equipments for manual arc welding consist of power source, current regulator, electrode holder and cables.
焊条电弧焊焊缝的断裂韧性与气体保护焊焊缝的断裂韧性相当。
Fracture toughness of both shielded metal arc welding and gas metal arc welding is almost the same.
文中所建的表达式，为CO_2电弧焊的研究和应用提供了理论依据。
The established equation provides a theoretical foundation for the study and application of CO_2 arc welding.
焊接涂铝钢首选的方法是电阻焊接，因为高温气焊和电弧焊毁坏涂层。
Somewhat higher spot-welding currents are needed than are used for unclad steel because of the low electrical resistance of the aluminum cladding.
基层的焊接，推荐采用手工电弧焊、埋弧焊以及二氧化碳气体保护焊。
Shielded Metal Arc Welding, Submerged-arc Welding and CO2 Arc Welding are recommended for base layer welding.
将电弧焊设备上的接地连接尽可能近地连接到将要焊接零件的焊接点上。
Connect the ground connection of the electric arc welding equipment as near as possible to the welding point on the part to be welded.
自1881年，俄国的贝纳尔多斯发明了电弧焊，到现在已经有100多年了。
Since 1881, Russia's Bernard Meadows invented the electric arc welding, up to now has been 100 years.
通过理论分析及实验，探讨了手工电弧焊焊条药皮中添加金属镁粉的脱硫效果。
By adding magnesium powder into the coating of electrode, the sulphurs removal in deposited metal was satisfactory.
焊接时尽量采用氩弧焊接，采用手工电弧焊时应采用小电流、快速焊，避免摆动。
Welding, as far as possible using argon arc welding, manual arc welding should be used in small current, fast welding, to avoid the swing.
结果表明，熔池表面和底部的温度都低于电弧焊，这是造成低稀释率的根本原因；
The result shows that the temperatures of molten pool surface and bottom are lower than those ones in arc welding. This is main cause of formation of low dilution rate.
手工电弧焊的电弧电压是一个难以控制的参数，有时能对焊接质量产生较大影响。
The arc voltage is not easily controlled in manual arc welding, sometimes it is damaged to the quality of welding.
应用高效的气体保护熔化极电弧焊焊接铝合金薄板时，容易出现熔池下塌、烧穿等焊接缺陷。
Welding defects such as collapse of molten pool, burning through, would like to happen in the high efficient gas shielded metal arc welding.
利用旋转电弧传感器，开展了水下湿法药芯焊丝电弧焊(FCAW)的V型坡口焊缝跟踪研究。
In this paper, we carried out a series of studies on the V-groove welding seam of the flux core arc welding (FCAW) with rotating arc sensor.
简体中文标题：焊接材料。带和不带气体保护的合金钢以及细晶粒钢电弧焊用管状焊条。分类。
English Name:Welding consumables - Tubular cored electrodes for metal arc welding with and without a gas shield of non alloy and fine grain steels - Classification;
本文研究了一种使用数据库及回归分析技术在电弧焊中预测焊道形状及选择最佳焊接参数的方法。
A method in which a data base and regression will be employed has been studied for predicting weld bead shape and selecting optimum welding parameters in arc welding processes.
针对手工焊条电弧焊(MMA)弧焊过程特点，建立了绝缘栅型晶体管逆变式弧焊电源控制系统。
Based on the characteristics of MMA welding process, a new control system of IGBT inverter arc welding power source is developed.
简体中文标题：焊接消耗品。高强度钢气体保护电弧焊用焊丝电极、焊丝、焊条和沉积金属。分类。
English Name: welding consumables - wire electrodes, wires, rods and deposits for gas-shielded arc welding of high strength steels - Classification.
简体中文标题：焊接消耗品。高强度钢气体保护电弧焊用焊丝电极、焊丝、焊条和沉积金属。分类。
English Name: welding consumables - wire electrodes, wires, rods and deposits for gas-shielded arc welding of high strength steels - Classification.
应用推荐