上述方法在热弯曲试验器分析中均得到了验证。
作为一个高科技怪胎我是地狱说服客户使用当时的新技术，热弯曲。
Being a tech freak I was hell bent on convincing the client to use the then NEW AND HOT technology.
运用有限元工具，对影响中厚钢板热弯曲成形中冷却收缩的主要因素进行了有限元数值模拟。
With the finite element method, the main factors that affecting the cooling contraction of the bent steel plate of medium thickness are simulated.
在后面章节中，中空板的最小弯曲半径是其厚度的175倍，只可以冷弯，不能热弯。
B. in a later chapter, hollow plate the smallest bending radius is 175 times of its thickness, can only cold bending, hot bending.
当把导线快速地(通过)来回弯曲折断时，部分功就转换成热，所以导线变热。
When a wire is broken by bending it back and forth rapidly, some of the work is transformed into heat and the wire gets hot.
在承受频繁的弯曲应力作用后，在其焊接热影响区萌生了裂纹源进而发生疲劳开裂。
In frequent bending stress condition, fatigue cracking occurred due to the cracking source had been initiated in welding heat affected zone.
结果表明，烧结-热等静压制作的硬质合金孔洞消除了，并且硬质合金的抗弯强度和弯曲疲劳寿命也大幅度提高。
The results showed that cemented carbide manufactured by sinter-HIP is free of porosity and transverse-rupture strength, bending fatigue life are also greatly increased.
盘管式加热器是化工厂的主要换热设备之一，其盘管的更换主要涉及胎具直径的确定和弯曲应力的消除。
Coiled pipe heater is one of the main heat exchangers in chemical works. Replacing coil is related to the definition of the mold diameter and the elimination of the winding stress.
本试验方法不仅适用于热双金属横向弯曲的测量，也适用于其他材料横向弯曲的测量。
This test method is not limited to thermostat metals and can be used for other materials for which the cross curvature must be measured accurately.
经瓷体强度实验、抗弯曲实验、耐焊接热实验、加速寿命实验，其各项指标均合格。
Strength and bending resistance test, welding heat test and highly accelerated life test (HALT) were retested up to grade.
本文之主要研究目的为探讨热管弯曲角度其热传性能的影响。
The purpose of this paper is to probe into the impact of the bending angle of heat pipe on its thermal performance.
可用于确定内膛弯曲度、身管热变形、弹丸偏心率、内弹道诸元和身管结构等对射弹散布的影响。
It may be used to determine the effects of bore curvature thermal deflection of the tube eccentricity of the projectile interior ballistics data and construction of gun tube on dispersion error.
针对一个被均匀加热的矩形截面梁由于不均匀的冷却过程所引起的弯曲变形问题，本文给出了一个热弹塑性分析解。
An analytical solution for elastoplastic bending of a hot free beam due to inhomogeneous cooling process is presented in this paper.
流槽损伤的主要形式是由弯曲力及热应力引起的变形和强烈的热作用引起的熔蚀。
The principal forms of the damages in the pouring spout are the deform caused by the bending forces and thermal stress as well as the fusion aroused by the intensive thermal effect.
对某大型液体火箭发动机的热试车数据及通过发动机模型仿真得到的故障数据进行动态时间弯曲分析，得到弯曲路径集，然后结合决策树方法进行了故障检测和诊断。
Through dynamic time warping analysis to the hot-fire test data and simulated fault data of a certain liquid rocket engine, the warped path sets were obtained.
结果表明，保护性高温烧结工艺的发热体可进行热态弯曲成形，表面没有发现裂纹，试样中的气孔已明显球化。
The result shows that the heating element of protect high temperature burning procedure could heat bend. No crack on the surface was found and pore was evidence spheroid.
采用焊管作为管坯 ，焊管弯曲采用专用模具热弯 ，焊接采用等离子弧焊。超塑成形采用多层模结构 ，用模具来控制波形。
Welded pipe that bended by hot bending method with a set of specific die and welded by plasma arc welding method was used as tubular blank of SPF.
主要研究了正交三维织物增强热塑复合材料的成型工艺，即成型厚度、成型温度对其弯曲性能的影响。
The molding technique to influence flexure property of orthogonal 3D woven reinforced resin composite were studied from the aspects of molding thickness and temperature.
随碳纤维比例的增大，该复合材料的拉伸强度、弯曲强度、弯曲模量及热变形温度均呈上升态势；而缺口冲击强度及击穿电压呈下降态势。
The results of experiments show that tensile strength, bend strength, bend modulus and heat deformation temperature of the composite materials are increased with the increase of carbon fibre content.
合成了两个系列以1，3，4-噻二唑为中心基团的弯曲型分子，结合偏光显微熔点仪（POM）观察和差示量热扫描法（DSC）研究了它们的液晶性能。
Two series of bent-core liquid crystals with 1,3,4- thiadiazole as the center unit were synthesized, their liquid crystalline properties were studied by POM and DSC.
冷弯薄壁型钢截面上的残余应力分布是弯曲型的，而热扎型钢或焊接型钢截面上残余应力分布是薄膜型。
Cold-formed steel cross section on the residual stress distribution is curved, and hot rolling steel or steel section on welding residual stress distribution is a thin film type.
我们的瓦片不会变的那么热，是因为其形状是弯曲的，弯曲的瓦片能够使空气从下面进行流通。”她说。
Our tiles get less hot because the modular is curved and with any curved tile you have air beneath keeping them cooler, " she said."
我们的瓦片不会变的那么热，是因为其形状是弯曲的，弯曲的瓦片能够使空气从下面进行流通。”她说。
Our tiles get less hot because the modular is curved and with any curved tile you have air beneath keeping them cooler, " she said."
应用推荐