测量过程全部由计算机控制。
对冲板流量计的测量过程进行试验分析。
The measuring process of the impact weighers is analyzed by experiments.
测量过程由微机控制进行。
紫外光源在测量过程可通过流变软件实现自动激活。
The UV light source can be triggered automatically by the rheometer software during the measurement.
测试中采用一种新的消光法，使测量过程简单可靠。
The new measuring process which is based on null measurement is simple and reliable.
检测圆锥管螺纹基面中径的方法有很多，但测量过程复杂。
There are many ways to measure base-level pitch diameter of cone-shaped thread.
结合某货车驾驶室外形的测量，介绍了ATOS的测量过程。
Through measuring the cab contour of a truck, measuring procedure by ATOS is presented.
量子测量难题的解决中对于量子测量过程的分析是必不可少的。
The analysis of quantum measurement process is necessary to the solution of quantum measurement problem.
提出一种将目标定位过程和测量过程分开的绝对距离测量系统。
An absolute range measuring system that can separate the target locating process from the measuring process is proposed in the paper.
根据用户指定的外部条件，触发器在适当的时刻启动测量过程。
To ensure that the desired portion of the signal is acquired, the trigger starts the measurement at the proper time according to some external condition.
本文介绍了地应力测量所使用的测量方法、测量过程和测量结果。
This paper introduces the method, process and results of the in-situ stress measurement.
本文对超声衰减系数和超声声速断层成像的测量过程进行了描述。
This paper describes the measurement procedure of ultrasonic attenuation coefficients and ultrasonic velocity tomography.
同时，PC机控制单片机系统驱动步进电机，完成整个光度测量过程。
Meanwhile, the PC controls the MCU to drive the step-motor to implement the whole measurement process.
在两次计量校准间隔期内，采用测量过程控制方法保证测量仪器的精度。
Measurement Process Control is adopted for a measuring instrument to guarantee its precision in the interval of two calibrations.
测量过程依次为读取图像、识别轮廓、拟合曲线、计算参数等几个步骤。
The measurement process was finished by steps of read images, identification profile, curve fitting, and calculate parameters.
该结果和实验吻合的很好，从而能够帮助我们深入地了解一些测量过程。
The results accord with the experiment's data and help us to be acquainted with the FC and ZFC process.
不先观察时域响应就随意使用指数窗作为测量过程的第一个步骤是不推荐的。
The arbitrary use of the exponential window without first looking at the time response is not recommended as the first step in the measurement process.
产品整个测量过程用电脑控制，其测量结果直接用数字显示粘度值，不用换算。
Products the whole measuring process is controlled by computer, the results measured directly with digital display viscosity value, not conversion.
产生误差的原因主要包括两个方面，测量过程的规范性和患者个体的心理因素。
The causes of errors mainly included two aspects, the standardization of measurement procedures and the psychological factor of individual patients.
ARM平台对整个测量过程数据予与实时图形化显示，并将数据存储于SD卡。
The ARM platform also showed the real-time graph of the measured data, saved the data in the SD card.
同时该系统利用专用LCD驱动器将测量过程和结果实时地在LCD上进行显示。
Meanwhile, the measuring and result can be displayed at real time on a LCD which is driven by a special LCD driver.
本文主要阐述如何对测量过程实施质量控制以保证设计、生产对测量的质量需要。
The paper mainly elaborates how to put in practice quality control about measure process. in order to quality require of measure in design and production.
在测量过程前，轴的转速必须恒定，过程中，不允许调整油门和改变机械运行条件。
It is essential that the shaft RPM be steadied prior to entering the measured course. Throttle and machinery operating conditions shall not be adjusted during the run.
本文对典型的化学测量过程进行了阐明，对有证参考物质的一般研制步骤进行了考察。
The typical process of chemical measurement has been illustrated, and the general steps of the preparation of the CRMs have been reviewed in this paper.
对消磁系统S矩阵测量过程和分析方法进行了仿真研究，调试了S矩阵专用测量程序。
The S matrix measurement method is studied by this simulation process, and a special software for S matrix measuring is also debugged with this process.
该方法在实际应用中简化了复杂的测量过程与计算，从而提高了对几何测量的工作效率。
It simplifies the complicated measures and calculation as well as raises Labour efficiency in the geometric calculation and measure work.
如果能自动地从航空遥感图像中提取出道路网，将会简化城市地物目标的分类和测量过程。
The classification and measuring procedure for geometrical objects of a city will be simplified if its main road network could be automatically extracted from aerial remote sensing images.
本文介绍一种适用于此类测量过程的数据处理方法，并通过具体的例子说明这种方法的使用。
In this paper a data processing method suitable for this kind of measurements is introduced. Some examples are also given to show the possibility to extend the application of this method.
按照国家标准，充油变压器的油中气体浓度至少是3个月测量一次，另外，测量过程十分复杂。
According to National Criteria, the measuring period for gas in oil concentrations of oil filled transformer is 3 months at least, and besides, the measuring procedure is complicated.
根据轧辊磨损度测量过程的特点及精度要求，对传感器电路系统的原理、组成及性能进行了分析。
According to the characteristic and the measuring accuracy of roller wear testing course, its principle, construction, and function of the sensor circuit are analysed.
应用推荐