待粘接剂固化后，管子、管接头体通过螺丝堵头凝接成一个整体。
After the adhesive is solidified, the pipe and the pipe joint body are screwed into a whole through the screw plug.
本发明摆动旋转接头由球型接头体，螺纹接头套，锁紧螺帽，大铜垫和两个球面转环构成。
The swinging rotating joint consists of spherical body, thread joint sleeve, locking screw nut, large copper washer and two spherical rings.
确定以某型号雷体为代表类型的水下兵器用金属承力件与复合材料的合理胶接接头方式，以达到理想的连接、防渗效果。
The reasonable bonding joint between load-bearing metal parts and composite for the present of a certain torpedo is decided to achieve the ideal bonding and leakproof.
本文将高匹配焊缝或热影响区(haz)淬硬层中含纵向裂纹的焊接接头简化为硬夹层含平行裂纹的力学不均匀体模型。
In the paper welded joints with a crack in transverse overmatched weld or HAZ were simplified into a model in which a transverse hard layer contains a crack parallel to the interfaces.
介绍了超低碳贝氏体wdb620钢的力学性能，用几种传统的焊接性试验方法对该钢焊接接头的力学性能及抗裂性进行了研究。
The mechanical properties of steel WDB620 are introduced. Some traditional tests about the mechanical properties and cracking resistance on its welded joint have been made.
带螺纹的工具接头必须经过正确地鉴别，然后被扭转至正确数值，以确保工具管柱牢固可靠而不损坏工具或管子体部。
The threaded tool joints must be correctly identified and then torqued to the correct value to ensure a secure tool string without damaging the tool or tubular body.
实施筒体的焊接工艺前，必须验证焊接接头的使用性能，从而证明压力容器筒体焊接工艺的重要性。
Welding joints must be certified before implementation of the welding process, thereby, the improvement of the welding process on barrel of pressure vessel is proved.
结果表明，钢体上开工艺槽导致焊后残余应力增加，对接头强度不利；钎缝厚度存在一最佳值。
The result showed that notch was disadvantageous to the strength of joints, and the optimal value of filler metal thickness existed.
采用虚拟裂纹扩展法对焊接接头力学不均匀体的断裂参量J积分进行了数值模拟分析。
The virtual crack extension method has been utilized to simulate the J-integral of non-uniform welded joints.
焊接接头是一个宏观力学不均匀体，力学不均匀性对焊接接头的动态断裂行为有重要的影响。
Welded joint is a mechanical heterogeneous body, and the mechanical heterogeneity has great effect on dynamic fracture behaviour of welded joint.
采用大的线能量焊接，形成较多的上贝氏体和粒状贝氏体组织，对改善接头性能有利。
With large welding heat input, more upper Bainite and granular Bainite form, which is benefit to improve the property of HAZ.
T CS铁素体不锈钢采用奥氏体型焊材，实芯焊丝、药芯焊丝和电焊条方法，焊接接头力学性能可以满足使用要求。
With austenitic welding material, solid wire, flux-cored wire and electrode, welded joint mechanical property of TCS ferritic stainless steel all can meet usability.
可对任意形状的带电体进行防护，解决相间距的不足，用于被损坏电缆修补，电力电缆中间接头侧面密封等问题。
It Can be charged for any body shape for protection, with space to solve the shortage, for repairing damaged cable, Power cable Joints side sealing problems.
焊接接头的耐点蚀性能明显下降，点蚀优先发生在高温热影响区所在的铁素体晶粒内。
Consequently, pitting corrosion resistance of the welded joint declines obviously and pitting preferentially occurs at ferrite phase in the high temperature HAZ near the fusion line.
连接头与传感器一体，使操作更加方便。
It is easy to operate thanks to proper combination of connectors and sensors.
广西京南水利枢纽右岸接头坝为避免梧昭公路改道 ，采取缩短接头坝长度、减少开挖措施 ，使基建面置于风化强烈、工程地质条件差的岩体上。
To avoid the Guiwu road being divagated, the right bank joint dam of the Jingnan WR pivotal project took some measures to shorten the joint dams length and decrease excavation.
利用二氧化碳保护焊、埋弧焊、手工电弧焊研究了高强度贝氏体钢板焊接接头的组织和力学性能。
The joint microstructure and mechanical properties of high strength bainitic steel plate were studied by CO2 gas shielded welding(CGSW), submerged arc welding(SAW) and manual arc welding(MAW).
本实用新型公开了一种用于螺纹接头的管材，其特征在于：在靠近管体的端部有一扩张段，在扩张段的端部有一翻边。
The utility model discloses a pipe used for screw ends, which is characterized in that a divergent section is close to the end of the pipe body, and the end of the divergent section has a flange.
高尔夫推杆上的瞄准器接头，瞄准器置于一盒体上，有一按键开关和一激光发射器。
A breech-sight tie-in of the golf club comprises a keyswitch and a laser emitter with the breech-sight is located on a box.
在较大焊接热输入条件下焊接，焊缝金属产生粗大先共析铁素体、过热区产生粗大粒状贝氏体，焊接接头低温冲击韧性因此降低。
The coarse primary ferrite appeared in weld metal, and coarse bainite appeared in heat-affected zone under larger heat input welding condition, which caused low...
框架材料：5英尺1英尺3 / 4 “胶合板大陆架减少了一半。油管钢箱梁焊接头管，另一管钢箱梁焊接的体壳的所在地管。
Frame Materials: 5 foot by 1 foot 3/4" plywood shelf cut in half. steel box tubing welded to head tube, another steel box tube welded to a BB shell and to a seat tube."
平衡铁素体和奥氏体两相组织在焊缝金属和热影响区中的比例，保证焊接接头的性能，是双相不锈钢焊接的基本要求。
The basic requirement of welding the steel 2205 is that the weld metal and heat-affected zone obtain a favorable phase balance and retain the performance as the base metal after welding.
平衡铁素体和奥氏体两相组织在焊缝金属和热影响区中的比例，保证焊接接头的性能，是双相不锈钢焊接的基本要求。
The basic requirement of welding the steel 2205 is that the weld metal and heat-affected zone obtain a favorable phase balance and retain the performance as the base metal after welding.
应用推荐