以套圈锁点为测量基准是较好的测量方法。
It is a better measuring method using the locking point of ring as a measurement basic point.
套圈部分沿着纵向轴线弯曲以形成弯曲部分。
The ferrule portion is bent along the longitudinal axis to form a bend.
轴承套圈的冷辗扩是一种以辗代车的先进工艺。
Cold rolling of bearing rings is a advanced process substituted for turning.
轴承零配件：套圈保持架密封件滚动体紧固套。
Bearing parts: rings, cages, seals, and rolling bodies, fastening sets.
轴承内孔或外表面与套圈一端面连接的套圈表面。
Bearing bore or outside the surface and the ferrule end face connected to a ring surface.
抡锤、坐草车、骑小马、套圈和打玩具枪，有很多呢。
Hammer strike, hay ride, pony ride, ring throwing, and toy guns. Lots of them.
对分离型轴承，必须在每个套圈端面上标上完整的标志。
Separate bearings, rings on each side must be marked on the surface of a sign of integrity.
套圈》反过来说就是圈套，一毛钱一次，套住什么得什么。
Ferrule:If it's conversed, that is a trap, ten fen for one time and the covered will be yours.
如轴承圆柱滚子、圆锥滚子、滚针、套圈等的在线自动检测。
Such as cylindrical roller bearings, tapered roller, needle, ring and other on-line automatic detection.
他们拆开检查坑或得分，这意味着该中心不应该使用的轴承套圈。
Disassemble them and check the bearing RACES for pits or scoring which mean the hub should not be used.
轴承套圈精密冷碾扩机床是一种加工轴承套圈精密毛坯的新技术。
The colded precision rolling machine for bearing ring is a new advanced technology for process precision bearing blanks.
该文提出了评价一次地震预报有效性的概率统计法(套圈模型)。
The paper puts forward the Probability Statistic Method of Evaluation Efficiency of an Earthquake Prediction (" Ringing-circle "Model).
一用于腕臂套置的腕臂套圈通过弹力带连接在U形前支架的横杆上。
Another ferrule that is used to enclose the wrist and antebrachium is linked to the crossbar of the U-shaped rack through elastic strings.
工业管道系统。锻制钢法兰和套圈。材料。机械性能。制造。试验。
Industrial pipeworks. Forged steel flanges and collars. Materials. Mechanical properties. Fabrication. Tests.
圆锥滚子轴承的套圈是重要的承载部件，对轴承的性能有着重要的影响。
Taper roller bearing race, a very important load-bearing component, has significant affection on the property of the bearing.
在铜管上安装阀门，然后轻轻地把压缩螺母和套圈移到阀门上并进行啮合。
Install the valve onto the copper tube and gently slide compression nut and ferrule up to the valve to engage.
以试验为基础，研究30204圆锥滚子轴承套圈参数与振动速度的关系。
Based on the experiment, the relation between ring parameter and vibration velocity of 30204 tapered rolling bearing is studied.
易之间的管材，管件常设大会：推入拟合套圈油管，直到管“点击”到位。
Easy, permanent assembly between the tubing and fittings: push the tubing over the fitting ferrule until the tubing "clicks" into place.
介绍了圆锥轴承套圈精密辗扩机的结构、控制原理及各主要组成部分的设计特点。
The structure, control principle and main part design features are introduced for precision rolling machine of the tapered bearing ring.
在磨削套圈沟道工序中，沟道磨削余量的大小对加工效率和表面质量影响非常大。
In the working procedure of grinding grooved raceway of the RACES, grinding stock removal of grooved raceway has an important effect on processing efficiency and surface quality.
针对双滚道滚动轴承套圈磨削加工过程中存在的问题，提出了动态控制磨削加工法。
Pointing at problems produced in grinding process of bearing rings with double raceways, the dynamic control grinding process method is put forward.
针对短时间内大量轴承套圈突然生锈的情况，分析了产生锈蚀的原因，提出了预防措施。
Because large quantity of bearing rings rusted in a short of time, the reason of causing rust was analyzed and preventive measures were given.
对单列角接触轴承，径向额定负荷为引起轴承套圈彼此相对纯径向位移的负荷的径向分量。
On the single row angular contact bearings, radial load rating of bearing rings relative to each other purely radial displacement of the load of the radial component.
管道管件应为非扩口压缩式三件构造，由套圈、螺帽和本体组成，适宜安装在不锈钢管道上。
Tube fittings shall be flare less compression type of three-piece construction consisting of ferrule nut and body suitable for use on ss tubes.
每个切削端都具有在其末端的切削头，主体部分，主体部分中的凹口以及定位于凹口中的套圈。
The cutting ends each have a cutting tip at a distal end, a body portion, a recess in the body portion and a retainer positioned in the recess.
每个切削端都具有在其末端的切削头，主体部分，主体部分中的凹口以及定位于凹口中的套圈。
The cutting ends each have a cutting tip at a distal end, a body portion, a recess in the body portion and a retainer positioned in the recess.
应用推荐