在最佳工艺条件下，钼的浸出率接近100%。
Under the optimum factors, the lixiviating rate of molybdenum was near 100%.
在最佳工艺条件下，产品收率可达99%以上。
Under the optimum conditions, the yield of the product can reach more than 99%.
结论在最佳工艺条件下，多糖得率为3.21%。
CONCLUSION Under the optimal conditions, the yield of polysaccharides is 3.21%.
在最佳工艺条件下，大蒜总黄酮得率达到3.99%。
Under the optimal extraction conditions, the yield of total garlic flavonoids reached 3.99%.
在最佳工艺条件下，电解锰废水锰的电沉积效率达到62。
The effect of electrolysis sediment of waster water in EMM, under the best productive condition, will reach 62.
在最佳工艺条件下，拒水等级可达到10级，拒油等级可达到7级。
Under optimum processing condition, we obtain a 10th grade in water proofing and a 7th in oil proofing rate.
在最佳工艺条件下，锰的浸出率达99%以上，银的浸出率达95%以上。
Under the optimum technological conditions, the leaching efficiencies of Mn and Ag are over 99% and 95% respectively.
结果表明，在最佳工艺条件下，产品收率可达95 %、纯度大于97%。
The results show that the yield is more than 95% and the purity more than 97% under the optimum conditions.
在最佳工艺条件下反应得到蔗糖多酯产率达到89.12%，酯化度6.8。
Under the optimum conditions the sucrose polyester (SPE) yield attained 89.12%, and the esterification degree reached 6.8.
该工艺提高了镍的回收率和产品纯度，在最佳工艺条件下，镍回收率大于90%，纯度大于40%。
The recovery ratio of nickel and product purity is increased. Under the optimal conditions, the recovery ratio of nickel is over 90%, the purity of nickel is over 40%.
结论：在最佳工艺条件下，八角总黄酮提取率为23.61%， 八角残渣总黄酮提取率为16.81%。
Under the above conditions, the yields of total flavonoids from star anise and its residue were 23.61% and 16.81%, respectively.
对压铸铝合金进行低温时效，在最佳工艺条件下，合金的平均拉伸强度提高10 %以上，布氏硬度提高30 %以上。
Low temperature aging for die casting al alloy under appropriate technological condition can increase average strength and Brinell hardness more than 10% and 30% respectively.
方法：运用正交设计选取微波法和超声法的最佳工艺条件，用均匀设计选取渗漉法的最佳工艺条件，比较三种方法在最佳工艺条件下的得率。
Design of microwave method and ultrasonic method base on orthogonal, and selecting the best processes of percolation method through uniform design, then compare with the amount of polysaccharide.
方法：在相同的工艺条件下，用不同的氮素代替玉米浆，改变配比寻找最佳方案。
Method:at the same condition, we use different N to be replacement of maize plasm and change the matching to find the best project.
确定了获得一定厚度液体层的最佳工艺参数，研究了液态或固态条件下稀土对扩散效果的影响，初步探讨了碳在固态与液态下的扩散机理。
The optimal parameters to obtain certain thickness of liquid case are decided, and effects of influence on diffusion of carbon has been studied as well as the diffusion mechanism.
在脂肪酶最佳处理工艺条件下，磨木浆与原浆相比，树脂含量下降了52.58%，而强度均有不同程度的提高。
Compared with the original pulp, resin content of the treated ground pulp with lipase under optimum condition decreased by 52.58 % and strength of the treated pulp increased in varying degrees.
在最佳处理工艺条件下，COD和氨氮的降解率分别达到94.1%和84.5%。
The degradation rate of COD and ammoniac nitrogen reached 94.1% and 84.5%, respectively.
在最佳运行条件下，研究了本工艺处理有机废水的性能和效果。
Under the optimal operating condition, the effect of organic wastewater treatment by this new process is studied.
在最佳碱浸工艺条件下，二氧化硅浸出率达到96%以上。
While in the optimum conditions of alkaline leaching, it is possible to extract 96% of silicon dioxide.
探讨了影响分离的主要因素，在最佳条件下，七种组分能分离完全，对合成工艺的中控分析。
Various factors related to the experiment were discussed and complared. At any rate, the optimum condition for complete seperation in time was given and could be satified for on line analysis.
在最优的工艺条件下XHP03是提取大豆低聚糖的最佳用膜。
XHP03 was chosen as the best ultrafiltration membrane under excellent conditions.
在最佳工艺参数条件下加入复合变质剂可进一步细化涂层的组织。
Under the optimum laser cladding parameters, adding modifying agent can further fine the microstructure of coating.
在最佳工艺参数条件下加入复合变质剂可进一步细化涂层的组织。
Under the optimum laser cladding parameters, adding modifying agent can further fine the microstructure of coating.
应用推荐